Filter
Top Products
The System Setup menu
08
44
En
1 Select ‘Data Management’ from the System Setup
menu.
See
Making receiver settings from the System Setup menu
above if you’re not already at this screen.
2 Select the setting you want to adjust.
•
MCACC Data Check
– Check the settings for any of
your MCACC presets using the on-screen display
(see
Checking MCACC preset data
below).
•
MCACC Data Copy
– Copy settings from one
MCACC preset to another (see
Copying MCACC
preset data
below).
•
Memory Rename
– Name your MCACC presets for
easy identification (see
Renaming MCACC presets
below).
•
Memory Clear
– Clear any MCACC presets that you
don’t want (see
Clearing MCACC presets
below).
Checking MCACC preset data
After you have completed
Automatically setting up for
surround sound (MCACC)
on page 8 or
Automatic
MCACC (Expert)
on page 36, you can check your
calibrated settings using the on-screen display.
1 Select ‘MCACC Data Check’ from the Data
Management setup menu.
2 Select the setting you want to check.
• It is useful to do this while a source is playing so you
can compare the different settings.
3 Select the MCACC preset that you want to check.
Use the
/
buttons if necessary to switch speakers/
settings.
4 Press
RETURN
to go back to the Data Check menu,
repeating steps 2 and 3 to check other settings.
5 When you're finished, press
RETURN
.
You will return to the Data Management setup menu.
Copying MCACC preset data
If you want to manually adjust the Acoustic Calibration
EQ (see
Manual MCACC setup
above), we recommend
copying your current settings
1
to an unused MCACC
preset. Instead of just a flat EQ curve, this will give you a
reference point from which to start.
1 Select ‘MCACC Data Copy’ from the Data
Management setup menu.
2 Select the MCACC preset you’ll be copying the
settings ‘From’ then specify where you want to copy
them (‘To’).
Make sure you don’t overwrite an MCACC preset you’re
currently using (this can’t be undone).
3 Select ‘Copy’ to confirm and copy the settings.
Copy Complete!
shows in the OSD to confirm the
MCACC preset has been copied, then you automatically
return to the Data Management setup menu.
Renaming MCACC presets
If you have several different MCACC presets that you’re
using, you may want to rename them for easier
identification.
1 Select ‘Memory Rename’ from the Data
Management setup menu.
System Setup
1.Auto MCACC
2.Surr Back System
3.Manual MCACC
4.Data Management
5.Manual SP Setup
6.Input Setup
7.Other Setup
: Exit
4.Data Management
:Return
a.MCACC Data Check
b.MCACC Data Copy
c.Memory Rename
d.Memory Clear
4.Data Management
:Return
a.MCACC Data Check
b.MCACC Data Copy
c.Memory Rename
d.Memory Clear
4a.MCACC Data Check
ENTER:Next :Return
1.Speaker Setting
2.Channel Level
3.Speaker Distance
4.Standing Wave
5.Acoustic Cal EQ
4a4.EQ Data Check
63
125
250
500
1k
2k
4k
8k
16k
TRM
63Hz : 0.0
MCACC M1 125Hz : 0.0
Ch [SBL] 250Hz : 0.0
500Hz : 0.0
1kHz : 0.0
2kHz : -1.0
4kHz :
-2.0
8kHz : -4.5
16kHz : -7.0
TRIM : 0.0
:Return
Note
1 The settings made in
Automatically setting up for surround sound (MCACC)
on page 8 or
Automatic MCACC (Expert)
on page 36.
4a2.Speaker Distance
MCACC M1. MEMORY 1
L : 2.0m
C : 2.0m
R : 2.0m
SR : 2.5m
SBR : 3.0m
SBL : 3.0m
SL : 2.5m
SW : 2.3m
:Return
4a3.Standing Wave
MCACC M1. MEMORY 1
Sranding Wave Control
: ON
Filter Ch [ SUB W. ]
TRIM : +12.0dB
No. 1 2 3
f : 110
Hz
: 110
Hz
: 110
Hz
Q : 3.0 : 3.0 : 3.0
: 12.0
dB
: 10.0
dB
: 12.0
dB
:Return
A
T
T
4.Data Management
:Return
a.MCACC Data Check
b.MCACC Data Copy
c.Memory Rename
d.Memory Clear
4b.MCACC Data Copy
:Cancel
From
[ M1. MEMORY 1 ]
To
[ M2. MEMORY 2 ]
Start Copy [Cancel ]
4.Data Management
:Return
a.MCACC Data Check
b.MCACC Data Copy
c.Memory Rename
d.Memory Clear
4c.Memory Rename
:Finish
MCACC Position Rename
M1 [ MEMORY 1 ]
M2 [ MEMORY 2 ]
M3 [ MEMORY 3 ]
M4 [ MEMORY 4 ]
M5 [ MEMORY 5 ]
M6 [ MEMORY 6 ]
VSX-2016_HY.book.fm 44 ページ ２００６年２月２４日 金曜日 午後１２時４０分