Filter
Top Products
16
• To check the (remaining) recording time, press DISPLAY.
(This can also be done during recording)
3 To stop recording, press STOP on the CD Recorder/Player.
‹
CD-SYNC and RECORD go out.
• To interrupt recording, press PAUSE.
‹ RECORD starts to flash. To resume, press PLAY on the
CD Recorder/Player.
After recording the display will show UPDATE for several
seconds.
Note:
- The CD Recorder/Player will not start until it recognizes
a digital signal. Although the reaction time is less than
200 milliseconds, the very beginning of the music may
sometimes not be recorded. If this happens, you can start
the recording manually (see digital recording -
unsynchronized).
- Recordings from DAT or DCC will only stop after 20 seconds
silence.
Only make analog recordings if digital recording is not
possible.
Preparing for analogue recording
1 Make sure the disc is absolutely free of scratches and
dust particles.
2 Press SOURCE repeatedly until:
‹ ANALOG appears on the display.
• If necessary, press DUAL to switch off the
DDUUAALL
mode;
DDUUAALL
will no longer appear on the display.
3 Press AUTO/MANUAL to switch between auto and manual
track numbering.
‹ If Auto is selected (preferred), AUTO TRACK appears on
the display.
• AUTO: The track number is automatically incremented after
a silence on the original of at least 3 seconds.
• MANUAL: Track numbers can be incremented manually by
pressing §. (minimum track length is 4 seconds.)
(This can also be done in AUTO mode)
• Track numbers cannot be changed after recording.
4 With the recorder stopped, press RECORD to enter Record
standby mode.
‹ RECORD will flash
5 Play the source first to set the optimal recording level on
the CD Recorder/Player.
6 Press REC LEVEL (+ or -) repeatedly until all the blue
segments on the Record/Play level bar light up continuously
but the red segments do not during the loudest passages.
‹ The display will show -3DB or 0DB or 3DB or 6DB
7 Stop the source.
Start analogue recording
1 To start recording, press PLAY on the CD Recorder/Player
and immediately start the source.
‹ RECORD lights continuously.The track number and
recording time used appear on the display.
• To record a 3-second silence at the start of a track,
press PAUSE.
• To check the (remaining) recording time, press DISPLAY.
(This can also be done during the recording)
2 To stop recording, press STOP on the CD Recorder/Player.
‹ RECORD will go out.
• To interrupt recording, press PAUSE.
‹ RECORD will start to flash. Resume at step 1.
After recording the display will show UPDATE for several
seconds.
Note: With AUTO TRACK on, the recorder will stop
automatically after a 20 seconds silence.
With AUTO TRACK off, the AUTO STOP mode is disabled.
CD SYNC SRC
SHUFFLESHUFFLE SCAN
RECORD
ERASE DUAL
TIME
TRACK
OVER
TOTAL REM TIME
DUBB 1
TOTAL REM TRACKAUTO TRACK TRACK
TRACK
FINALIZE
CD SYNC SRC
SHUFFLESHUFFLE SCAN
RECORD
FINALIZE
ERASE DUAL
TIME
TRACK
OVER
TOTAL REM TIME
DUBB 1
TOTAL REM TRACKAUTO TRACK TRACK
TRACK
CD SYNC SRC
SHUFFLESHUFFLE SCAN
FINALIZE
TIMETOTAL REM TIME
REPEAT 1 REPEAT 1DIG
DUBB 1
TOTAL
PAUSE
PAUSE PROGPROGOPTANALOG
REM TRACKAUTO TRACK TRACK
DISPLAY
SOURCE
REC LEVEL
DUAL
DISPLAY
PHONES
O
P
E
N
C
LO
S
E
O
P
E
N
C
LO
S
E
COMPACT DISC RECORDER CDR765
C
D
S
Y
N
C
S
C
A
N
R
E
W
R
IT
A
B
L
E
R
E
C
O
R
D
C
D
TIME
TRACK
OVER
TOTAL
REM
TIME
REPEAT 1
REPEAT 1
DIG
DUBB 1
TOTAL
PAUSE
PAUSE
REM
TRACK
Analogue recording from an external source
English
RECORDING