Filter
Top Products
40
Using the Remote Controller RC-518M with Your Other AV
Components
Connecting your -compatible Onkyo CD player, DVD
player, or cassette recorder to the HT-R510 via allows
you to control your system with the HT-R510’s remote con-
troller by pointing it at the HT-R510. This allows you to con-
trol components that are out of sight, for example, in a
cabinet. Since you don’t have to enter any special codes, or
do any programming, allows you to control these compo-
nents quickly and easily. See page 19 for connection infor-
mation. See page 41 for operating information.
In addition, you can control an AV component made by
another manufacturer by entering the appropriate manufac-
turer’s code into the remote controller.
Note:
•To use the function, you must make an connection
and an analog RCA/phono connection between the AV
component and your HT-R510, even if they are connected
digitally.
Entering the Manufacturer’s Code
If you’re using an Onkyo CD player connected to the
HT-R510’s connector, an Onkyo AV component without
an connection, or an AV component made by another
manufacturer, do the following.
If it works as expected, the code has been entered correctly.
If not, go back to step 3 and try again.
Note that with some manufacturer’s AV components, some
of the remote controller’s buttons may not work as expected.
By default, the [CD/DVD] button is set to code 316,
which is for use with an -compatible Onkyo DVD
player connected to the HT-R510’s connector. To
control an -compatible Onkyo CD player connected
to the HT-R510’s connector, you must enter code
300. To control an Onkyo DVD player without an
connection, you must enter either code 301 or 313. The
[CD/DVD] button can be used with only one AV compo-
nent.
RC-518M
1
Determine the appropriate manufacturer’s
code from the following list.
Where several codes are listed, try the first one, and
if that doesn’t work, try the others until you find one
that does.
2
While holding down the remote controller’s
[VCR], [TV], [CABLE/SAT], or [CD/DVD] but-
ton, press the [ENT] button.
For the [CD/DVD] button, you can enter a CD code
or DVD code, not both. And for the [CABLE/SAT]
button, a Cable code or Satellite code, not both.
3
Within 10 seconds, use the remote control-
ler’s number buttons to enter the manufac-
turer’s code.
4
Check to see if you can control the AV com-
ponent from the remote controller.
Manufacturer TV VCR DVD Cable Satellite
AIWA 137
AKAI 227
DENON 302
ECHOSTAR 500
EMERSON 228
FISHER 200
100, 101, 102,
140
GE 103, 104
GE • PANA 201, 202
GE • RCA 203
GEMINI 401
GENERAL
INSTRUMENT
501
G.I. 400
GO VIDEO 105, 106, 107
GOLD STAR 204, 205 108
HAMLIN
402, 403, 404,
405
HITACHI 206, 207 103, 109 303 502
HUGHES
NETWORK
SYSTEM
503
JERROLD
406, 407, 408,
409, 410, 411,
412, 413, 414
JVC 208
110, 111, 112,
113
304
KENWOOD 305
MACOM 415, 416, 417
MAGNAVOX 209, 210 114, 115, 116 306 418
MARANTZ 211 307
MITSUBISHI
117, 118, 119,
120, 121, 139
308
NEC 136
OAK 419, 420, 421
ONKYO
301, 313,
316 (for
DVD),
300 (for CD)
PANASONIC 212, 213 122, 123 309 422, 423 504, 505, 506
PHILIPS 214 114
424, 425, 426,
427, 428, 429
PIONEER 215 310 430, 431
PRIMESTAR 507
PROSCAN 216 311 508, 509, 510
RCA
217, 218, 219,
220, 229, 230
109 311 508, 509, 510
S.ATLANTA 432, 433, 434
SAMSUNG 221, 222 124, 125, 126 304 435
SHARP 223 127, 128
SHINTOM 138
SONY 224
129, 130, 131,
132, 133, 141
312 511
TOCOM 436
TOSHIBA 134 313 512
YAMAHA 314
ZENITH 225, 226 135 315 437, 438