Filter
Top Products
30
ENGLISH
BASIC
CONNECTIONS
BASIC OPERATION
ADVANCED
CONNECTIONS
SETUP
ADVANCED
OPERATION
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTIONS
ADVANCED
OPERATION
RECALLING A PRESET STATION
1.
DISPMULTIAUTO TUNED STV
–
OFFNIGHTPEAK ANALOG
DIGITAL
ATT
SLEEP
SURR
AUTO
DIRECT DISC 6.1MTX 6.1SPKRBEQ
DIGITAL
SURROUND
AAC
PCM
L
C
R
SLSSR
LFE
1.
1
.
(Using the unit)
1.
Select the desired preset station by pressing
the 1 or 2
cursor
buttons on the front panel
(Using the remote controller)
1.
Press the PRESET + or – buttons to select the
desired preset station, or input your desired
preset channel with the numeric buttons on
the remote controller.
PRESET SCAN
3
.
1
.
3
.
3
.
(Using the remote controller)
1.
Press the P.SCAN on the remote controller.
“PRESET SCAN” appears on the display and
then the preset station with the lowest preset
number is recalled fi rst.
2.
Preset stations are recalled in sequence (No.1
→ No.2 → etc.) for 5 seconds each.
No stored preset number will be skipped.
3.
You can fast forward the preset stations by
pressing the PRESET + continuously.
When the desired preset station is received,
cancel the preset scan operation by pressing
the CL button or P.SCAN on the remote
controller.
TUNER OPERATION (PRESET MEMORY)
With this unit you can preset up to 50 FM/AM stations
in any order.
For each station, you can memorize the frequency
and reception mode if desired.
AUTO PRESET MEMORY
This function automatically scans the FM and AM
band and enters all stations with proper signal
strength into the memory.
DISP MULTI AUTO TUNED STV
–
OFFNIGHT PEAK ANALOG
DIGITAL
ATT
SLEEP
SURR
AUTO
DIRECT DISC 6.1MTX 6.1SPKRB EQ
DIGITAL
SURROUND
AAC
PCM
L
C
R
SL SSR
LFE
4. 1. 3.2. 5. 2.
1.
To select FM, press the BAND button on the
front panel.
2.
While pressing the MEMORY button, press the
2 cursor button.
“AUTO PRESET” will appear on the display,
and scanning starts from the lowest frequency.
3.
Each time the tuner fi nds a station, scanning
will pause and the station will be played for fi ve
seconds.
During this time, the following operations are
possible.
The band can be changed by the BAND button.
4.
If no button is pressed during this period, the
current station is memorized in location Preset
01.
If you wish to skip the current station, press the
3 cursor button during this period, this station
is skipped and auto presetting continues.
5.
Operation stops automatically when all 50
preset memory positions are fi lled or when
auto scanning attains the highest end of all
bands. If you desire to stop the auto preset
memory at anytime, press the CLEAR button.
Note:
It is possible that existing preset memory positions
will be overwritten.
MANUAL PRESET MEMORY
2.
3
.
DISPMULTIAUTO TUNED STV
–
OFFNIGHTPEAK ANALOG
DIGITAL
ATT
SLEEP
SURR
AUTO
DIRECT DISC 6.1MTX 6.1SPKRBEQ
DIGITAL
SURROUND
AAC
PCM
L
C
R
SLSSR
LFE
3. 2. 4.
(Using the unit)
1.
Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
2.
Press the MEMORY button on the front panel.
“– –“ (preset number) starts blinking on the
display.
3.
Select the preset number by pressing the 1
or 2
cursor
buttons, while this is still blinking
(approx. 5 seconds)
4.
Press the MEMORY button again to enter. The
display stops blinking.
The station is now stored in the specifi ed preset
memory location.
(Using the remote controller)
1.
Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
2.
Press the MEMO button on the remote
controller. “– –“ (preset number) starts blinking
on the display.
3.
Enter the desired preset number by pressing
the numeric buttons.
Note:
When entering a single digit number (2 for example),
either input “02” or just input “2” and wait for a few
seconds.
SURROUND SPEAKER B SYSTEM
The Surround Speaker B system is a function which
allows you to listen to the same source in a room other
than the room in which the unit is located.
The operations possible with the Surround speaker
function are explained briefl y below.
ANOTHER ROOM PLAYBACK USING THE
S (SURROUND) SPEAKER B TERMINALS
The unit allows you to connect another set of
speakers and place them in a another room or
separated area for listening to music.
1
.
2
.
1.
Press the Z.SPKR button on the remote
controller. The unit enters surround speaker
B mode and the “SPKR B” will appear on the
display.
2.
The volume of S. SPEAKER B is interlocked
with the main volume.
Notes for SURROUND SPEAKER B
• SURROUND SPEAKER B On/ Off is available in
main room only.
• SURROUND SPEAKER B
output terminals can be
used when the SURROUND BACK SPEAKER is set
NONE in SPEAKER SETUP menu. (See SPEAKER
SETUP, page 21)
• “The Surr. Back Speakers are in use” is displayed
by pressing the Z. SPKR button on the remote
controller
when the SURROUND BACK SPEAKER
is set except NONE in SPEAKER SETUP menu. (See
SPEAKER SETUP, page 21)
• Surround Speaker B function is unavailable, while
the unit is 7.1 CH input mode.