Filter
Top Products
52
ENGLISH
S.SPEAKER B
DIGITAL
RLVIDEO
S-VIDEO
AUX 1 INPUT
AUDIO
SETUP
SIMPLE
7.1 CH INPUT
PURE
T-MO D E
SURROUND
MEMORY
DISPLAY
ATT
MUTE
STANDBY
INPUT SELECTOR
VOLUME
UP
DOWN
AV SURROUND RECEIVER SR4002
DIRECT
AUTO
HT-EQ
EXIT
MENU
MODE
BAND
CLEAR
ENTER
PHONES
POWER ON/STANDBY
SETUP MIC
7.1 CH INPUT (SR4002)
MULTI (SR5002)
SIMPLE
SETUP
EXIT ATT
FRONT KEY (BUTTON) LOCK OF THE UNIT
If the SIMPLE SETUP and EXT buttons on the front
panel are both pressed at the same time for three
seconds or more, all the buttons on the front panel,
(excluding the POWER ON/OFF button), as well as
the INPUT SELECTOR knob and VOLUME knob,
will become locked. “F-KEY LOCK!” will appear in
the display.
Release the lock by pressing the same two keys
again at the same time for three seconds or more.
“F-KEY UNLOCK” will appear in the display, and the
keys will unlock.
GENERAL MALFUNCTION
If the equipment malfunctions, this may be because
an electrostatic discharge or AC line interference has
corrupted the information in the equipment memory
circuits. Therefore:
- disconnect the plug from the AC line supply
- after waiting at least three minutes, reconnect
the plug to the AC line supply
- re-attempt to operate the equipment
Memory backup
• In case a power outage occurs or the power
cord is accidentally unplugged, this unit is
equipped with a backup function to prevent
memory data such as the preset memory
from being erased.
HOW TO RESET THE UNIT
Should the operation or display seem to be abnormal,
reset the unit with the following procedure.
To turn on the SR4002, press and hold the 7.1CH
INPUT and ATT buttons simultaneously for 3 seconds
or more.
To turn on the SR5002, press and hold the MULTI
and ATT buttons simultaneously for 3 seconds or
more.
Remember that the procedure will reset the settings
of the SOURCE, Surround mode, delay time, TUNER
Note:
Sometimes, when “PROTECT” is shown on the unit’s display, the standby indicator fl ashes slowly (twice a second).
When this happens, turn off the unit’s power and remove the power cable. Then follow the procedure described below:
• Check to ensure that the speaker cables connected to the unit have not been connected with + and - connections reversed.
(Check that the playback volume is not greater than the unit can handle.)
• Check that the playback volume is not greater than the unit can handle.
After completing the above checks, connect the power cable and switch the unit back ON using the remote control.
Then, after reducing the volume, start playback and check that “PROTECT” is not appearing on the display and that there is no problem with speaker connections to the unit or
with sound reproduction.
If the same problem re-occurs, please contact your local service center to have it repaired.
On rare occasions, the unit will go into standby mode with the standby indicator fl ashing rapidly (eight times a second).
When this happens, it means that some major problem has occurred with the unit.
Quickly disconnect the power cable and take the unit to your local service center to have it repaired.
XM SATELLITE RADIO
If a problem should arise, fi rst check the following.
1. Are the connections correct?
2. Have you operated the receiver according to the operating instructions?
3. Are the speakers and other components operating properIy?
If this unit is not operating properly, Check the items listed in the table beIow. Should the problem persist, there may be a malfunction. Disconnect the power immediately
and contact your store of purchase.
SYMPTOM CAUSE REMEDY
“ANTENNA” is displayed. XM terminal and the XM Mini-Tuner and Home Dock is not
properly connected.
Check that the connection are correct.
“NO SIGNAL” is displayed. The signal cannot be received. Reposition your XM Mini-Tuner and Home Dock.
Receiving only XM channels
0 and 1.
The XM Tuner is not activated. Contact XM Radio.