Marantz SR4002/SR5002 Stereo Receiver User Manual


  Open as PDF
of 60
 
42
ENGLISH
2.
While pressing the MEMO button, press the 2
cursor button.
“AUTO PRESET” will appear on the display,
and scanning starts from the lowest frequency.
3.
Each time the tuner fi nds a station, scanning
will pause and the station will be played for fi ve
seconds.
During this time, the following operations are
possible.
The band can be changed by the BAND button.
4.
If no button is pressed during this period, the
current station is memorized in location Preset
02.
If you wish to skip the current station, press the
3 cursor button during this period, this station
is skipped and auto presetting continues.
5.
Operation stops automatically when all 50
preset memory positions are fi lled or when
auto scanning attains the highest end of all
bands. If you desire to stop the auto preset
memory at anytime, press the CLEAR button.
Note:
It is possible that existing preset memory positions
will be overwritten.
MANUAL PRESET MEMORY
CAT
P.SCAN
CAT
T.MODE
+10
11 22 33
44 55 66
77 88 99
00
HT-EQ
MULTI/
MENU
SPKR A/B
INFO
CH/
INPUT
M-SPKR
MUTE
EX/ES
VIRTUAL
CS
VOLUME
dts
P.DIRECT
7.1CH IN
STEREO
NIGHT
M-CH ST
AUTO
SURROUND
SLEEP
DISPLAY
A/D
LIP SYNC/
CL
MEMOMEMO
3.
2.
SETUP
SIMPLE
PURE
T
SURROUND
MEMORY
DISPLAY
CEIVER SR5002
DIRECT
AUTO
HT-EQ
EXIT
MENU
MODE
BAND
ENTER
3. 2. 4.
(Using the unit)
1.
Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
2.
Press the MEMORY button on the front panel.
“– –“ (preset number) starts blinking on the
display.
3.
Select the preset number by pressing the 1
or 2
cursor
buttons, while this is still blinking
(approx. 5 seconds)
4.
Press the MEMORY button again to enter. The
display stops blinking.
The station is now stored in the specifi ed preset
memory location.
(FM) TUNING MODE (AUTO STEREO OR MONO)
P.SCAN
CAT
123
456
789
0
+10
T.MODET.MODE
HT-EQ
SPKR A/B
CH/
INPUT
MUTE
EX/ES
VIRTUAL
CS
VOLUME
dts
P.DIRECT
l/
OFF
ON
SET
7.1CH IN
STEREO
NIGHT
M-CH ST
AUTO
SURROUND
SLEEP
DISPLAY
A/D
LIP SYNC/
MEMO
CL
SOURCE
DIGITAL
RLVIDEO
S-VIDEO
AUX 1 INPUT
AUDIO
T-MO D E
MEMORY
DISPLAY
ATT
MUTE
VOLUME
UP
DOWN
EXIT
BAND
CLEAR
ENTER
When in the auto stereo mode, AUTO indicator will
be illuminated on the display.
The “ST” indicator is illuminated when a stereo
broadcast is tuned in.
At open frequencies, the noise is muted and the
“TUNED” and “ST” indicators are not illuminated.
If the signal is weak, it may be diffi cult to tune into
the station in stereo. In such a case, press the
T-MODE button on the front panel or remote
controller.
“AUTO” indicator is not illuminated, if FM stereo
broadcasts are received in monaural and the “ST”
indicator is not illuminated.
To return to auto stereo mode, press the T-MODE
button or press T-MODE button on the remote
controller
again. AUTO indicator is illuminated on the
display.
PRESET MEMORY
With this unit you can preset up to 50 FM/AM stations
in any order.
For each station, you can memorize the frequency
and reception mode if desired.
AUTO PRESET MEMORY
This function automatically scans the FM and AM
band and enters all stations with proper signal
strength into the memory.
MULTI
SPEAKER
DIGITAL
RLVIDEO
S-VIDEO
AUX 1 INPUT
AUDIO
SETUP
SIMPLE
MULTI
PURE
T-MO D E
SURROUND
MEMORY
DISPLAY
ATT
MUTE
STANDBY
INPUT SELECTOR
VOLUME
UP
DOWN
AV SURROUND RECEIVER SR5002
DIRECT
AUTO
HT-EQ
EXIT
MENU
MODE
BAND
CLEAR
ENTER
PHONES
POWER ON/STANDBY
SETUP MIC
2. 2. 5.4. 1. 3.
1.
To select FM, press the BAND button on the
front panel.
BASIC OPERATION
(TUNER)
LISTENING TO THE TUNER
Frequency scan step for AM is selectable.
Default setup is 10 kHz step, if your country’s
standard is 9 kHz step, press BAND button on the
remote controller more than 6 seconds. Scan step
will change.
Note:
Preset memory for the tuner will clear by changing
this setup.
AUTO TUNING
-
T.DISP
F.DIRECT
PTY
PRESET
+
TUNINGTUNING
--
++
REC
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
2.
P.SCAN
T.MODE
123
456
789
INPUT
EX/ES
VIRTUAL
CS
dts
P.DIRECT
STEREO
NIGHT
M-CH ST
AUTO
SURROUND
SLEEP
DISPLAY
LIP SYNC/
BAND
1.
DIGITAL
SETUP
SIMPLE
PURE
T-MO D E
D
MEMORY
DISPLAY
M
DOWN
DIRECT
HT-EQ
EXIT
MENU BAND
CLEAR
ENTER
1.2.
(Using the unit)
1.
To select tuner and desired band (FM or AM),
press the BAND button on the front panel.
2.
Press the
3 or 4 cursor buttons
on the front
panel for more than 1 second to start the auto
tuning function.
3.
Automatic searching begins then stops when a
station is tuned in.
(Using the remote controller)
1.
To select tuner and desired band (FM or
AM), press the BAND button on the remote
controller.
2.
Press the 5 or 6
for more than 1 second on
the remote controller.
3.
Automatic searching begins then stops when a
station is tuned in.
If tuning does not stop at the desired station, use to
the “Manual tuning” operation.
MANUAL TUNING
-
T.DISP
F.DIRECT
PTY
PRESET
+
TUNINGTUNING
--
++
BASS
TREBLE
REC
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
2.
P.SCAN
T.MODE
123
456
789
INPUT
EX/ES
VIRTUAL
CS
dts
P.DIRECT
STEREO
NIGHT
M-CH ST
AUTO
SURROUND
SLEEP
DISPLAY
LIP SYNC/
BAND
1.
DIGITAL
SETUP
SIMPLE
PURE
T-MO D E
D
MEMORY
DISPLAY
M
DOWN
DIRECT
HT-EQ
EXIT
MENU BAND
CLEAR
ENTER
1.2.
(Using the unit)
1.
To select tuner and desired band (FM or AM),
press the BAND button on the front panel.
2.
Press the
3 or 4 cursor buttons
on the front
panel to select the desired station.
(Using the remote controller )
1.
To select tuner and desired band (FM or
AM), press the BAND button on the remote
controller.
2.
Press the 5 or 6 on the remote controller to
tune in the desired station.
DIRECT FREQUENCY CALL
CAT
P.SCAN
CAT
T.MODE
+10
11 22 33
44 55 66
77 88 99
00
HT-EQ
MULTI/
SPKR A/B
CH/
INPUT
M-SPKR
MUTE
EX/ES
VIRTUAL
CS
VOLUME
dts
P.DIRECT
l/
OFF
ON
SET
7.1CH IN
STEREO
NIGHT
M-CH ST
AUTO
SURROUND
SLEEP
DISPLAY
A/D
LIP SYNC/
MEMO
CL
SOURCE
3.
-
T.DISP
PTY
TUNING
PRESET
-
++
F.DIRECTF.DIRECT
EXIT
/SET UP
REC
2.
P.SCAN
T.MODE
123
456
789
HT-EQ
INPUT
EX/ES
VIRTUAL
CS
dts
P.DIRECT
7.1CH IN
STEREO
NIGHT
M-CH ST
AUTO
SURROUND
SLEEP
DISPLAY
A/D
LIP SYNC/
BAND
1.
1.
To select tuner and desired band (FM or
AM), press the BAND button on the remote
controller.
2.
Press the F.DIRECT on the remote controller,
display will show “FREQ - - - -”.
3.
Input your desired station’s frequency with the
numeric buttons on the remote controller.
4.
The desired station will automatically be tuned.
 previous next