Filter
Top Products
44
ENGLISH
LISTENING TO XM SATELLITE RADIO
(SR5002 ONLY)
SELECTING AN INPUT SOURCE
Before you can listen to XM Satellite Radio, you must
fi rst select the input source on the SR5002.
MULTI
SPEAKER
MULTI
PURE
SURROUND
STANDBY
INPUT SELECTOR
AV SURROUND RECEIVER SR5002
DIRECT
AUTO
HT-EQ
MODE
PHONES
POWER ON/STANDBY
SETUP MIC
1.
P.SCAN
T.M ODE
+10
HT-EQ
INPUT
EX/ES
VIRTUAL
CS
dts
P.DIRECT
l/
OFF
ON
SET
7.1CH IN
STEREO
NIGHT
M-CH ST
AUTO
SURROUND
SLEEP
DISPLAY
A/D
LIP SYNC/
MEMO
BAND
CL
SOURCE
112233
445566
778899
00
2.
TAPE
REMOTE CONTROLLER
RC5001SR
MD
CDR
CD
DVD
AMP
AUX2
VCR
DSS
TV
BASS
TREBLE
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
AUX1
TUNERTUNER
1.
MULTI
SPEAKER
DIGITAL
RLVIDEO
S-VIDEO
AUX 1 INPUT
AUDIO
SETUP
SIMPLE
MULTI
PURE
T-MODE
SURROUND
MEMORY
DISPLAY
ATT
MUTE
STANDBY
INPUT SELECTOR
VOLUME
UP
DOWN
AV SURROUND RECEIVER SR5002
DIRECT
AUTO
HT-EQ
EXIT
MENU
MODE
BAND
CLEAR
ENTER
PHONES
POWER ON/STANDBY
SETUP MIC
2.
(Using the SR5002)
1.
Turn the INPUT SELECTOR knob to select
“TUNER”.
2.
Press the BAND button to select XM band.
(Using the remote controller)
1.
To select tuner, Press the TUNER button twice
within two seconds on the remote controller.
2.
Press the BAND button to select XM band.
CHECKING THE XM SIGNAL STRENGTH
AND RADIO ID
-
F.DIRECT
PTY
TUNING
PRESET
-
++
ENTER
EXIT
T.TO NE
/SET UP
BASS
TREBLE
REC
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
T.DISPT.DISP
1.
1.
Press the T.DISP button 3 times to displayed
Signal Status.
SIGNAL:
• The display changes as shown below according to
the receiving condition.
SIGNAL: ■■■■■■
SIGNAL: STRONG
(Signal strength is good)
SIGNAL: ■■■■
SIGNAL: MARGINAL
(Signal strength is Marginal)
SIGNAL: ■■
SIGNAL: WEAK
(Signal strength is poor)
XM NO SIGNAL
SIGNAL: NON
(Loss of the signal)
2.
Adjust the antenna location until signal strength
is good.
3.
Select channel 0 (XM000) with the 3 or 4
cursor buttons of the SR5002 or the Q or
R buttons of the remote controller.
MULTI
SPEAKER
SETUP
SIMPLE
MULTI
PURE
SURROUND
DISPLAY
STANDBY
INPUT SELECTOR
AV SURROUND RECEIVER SR5002
DIRECT
AUTO
HT-EQ
EXIT
MENU
MODE
ENTER
PHONES
P
OWER ON/STANDBY
SETUP MIC
3.
-
T.DISP
F.DIRECT
PTY
TUNING
PRESET
-
++
REMOTE CONTROLLER
TAP E
MENU
ENTER
EXIT
INFO
T.TONE
/SET UP
BASS
TREBLE
REC
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OF F
ATT.
MD
CDR
CD
AMP
AUX2
TUNER
AUX1
DVD VCR
DSS
TV
3.
• The Radio ID is displayed.
XMOOORADIO ID
Notes:
• If “ANTENNA” appears in the front panel display,
the XM Mini-Tuner and Home Dock may not be
connected to the XM terminal on the rear panel of
this unit properly.
• The ATT function is also effective when XM is
selected.
SWITCHING XM INFORMATION IN THE FRONT
PANEL DISPLAY
You can display XM information (such as artist name/
song title, category or signal status) for the channel
currently selected in the front panel display.
-
F.DIRECT
PTY
TUNING
PRESET
-
++
ENTER
EXIT
T.TO NE
/SET UP
BASS
TREBLE
REC
AUDI O
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
T.DISPT.DISP
1.
1.
Press the T.DISP button to displayed
Artist name/Song title
Channel category
Channel number/name
Signal Status
When the Channel number/name is displayed:
XMO40:DeepTrc
40:DeepTracks
(If text is more than 13 characters long, the text is
scrolled.)
Note:
The front Panel display can indicate up to 13 alphanumeric
characters at once. If the information contains more then
13 characters, the information scrolls from right to left.