Filter
Top Products
48
OPERATOR CONVENIENCES
MICROPROCESSOR RESET
If your transceiver seems to be malfunctioning, resetting
the microprocessor default settings may resolve the
problem.
INITIAL SETTINGS
For each VFO, the factory defaults for operating
frequency and mode are as follows:
• VFO A: 14.000.000 MHz/ USB
• VFO B: 14.000.000 MHz/ USB
The Conventional and Quick memory channels have no
data stored.
PARTIAL RESET
Do Partial Reset if a button or control does not function
according to the instructions in this manual. The
following are not erased by Partial Reset.
• Memory channel data
• Menu settings
• Antenna tuner preset data
• ANT 1/ANT 2 data.
To do Partial Reset, press [A/B]+[ ].
• “HELLO” appears on the display.
FULL RESET
Do Full Reset if you want to erase all data in all memory
channels. In addition, this function resets all settings,
that you customized, to the factory defaults, i.e. menu
settings, antenna tuner preset data, etc.
To do Full Reset, press [A=B]+[ ].
• “HELLO” appears on the display.
Note:
The IF filter selection in Menu No. 46 will not be reset.
SWITCHING ANT 1/ ANT 2
After connecting antenna feed line to the ANT 1
connector and/or ANT 2 connector on the rear panel,
select ANT 1 or ANT 2, depending on which antenna is
used for transmitting and receiving.
Press [ANT] to select ANT 1 or ANT 2.
• “ANT 1” or “ANT 2” appears to show which antenna
is selected.
The ANT 1/ANT 2 setting will automatically be stored in
the current band. Each time you select the same band,
the same setting will automatically be selected.
The frequency range of each band is shown below.
Note:
Connect an external antenna tuner to the ANT 1 connector
only. After connecting this tuner correctly and selecting ANT 1, the
internal tuner will always be bypassed.
FREQUENCY LOCK FUNCTION
Frequency Lock disables some buttons and controls to
prevent you from accidentally activating a function or
disturbing current settings.
Press [F.LOCK] to toggle Frequency Lock ON or OFF.
•“F.LOCK” appears when the function is ON.
The following buttons and controls are disabled by
Frequency Lock:
•Tuning control • MULTI/CH control
• QUICK MEMO [MR] • QUICK MEMO [M.IN]
• [FINE] • [REV] • [CLR]
• [ENT] • [LSB/USB] • [CW/FSK]
• [FM/AM] • [1MHz] • [UP]/[DOWN]
• [SPLIT] • [A/B] • [M/V]
• [A=B] • [SCAN] • [M>VFO]
• [M.IN]
Note:
◆
After activating Frequency Lock, the
MULTI/CH
control and
[UP]/[DOWN]
are still available in Menu mode.
◆
After activating Frequency Lock, you can still change the transmit
frequency with the
Tuning
control while using the TF-SET
function.
◆
After activating Frequency Lock, the
MULTI/CH
control is still
available for selections other than frequency and memory
channel changes.
◆
After activating Frequency Lock,
[CLR]
is still available in some
situations.
Frequency Range
(MHz)
Frequency Range
(MHz)
14.50 ~ 18.50
18.50 ~ 21.50
21.50 ~ 25.50
25.50 ~ 30.00
30.00 ~ 60.00 (TS-570S)
0.03 ~ 2.50
2.50 ~ 4.10
4.10 ~ 7.50
7.50 ~ 10.50
10.50 ~ 14.50