Filter
Top Products
11
Basic Operations
Signal indicators
Speaker indicators
Basic adjustment auto memory
This unit memorizes sound settings for each source ....
• when you turn on the power,
• when you change the source, and
•
when you change the analogue/digital input mode (see page 14).
When you change the source, the memorized settings for the
newly selected source are automatically recalled.
The following can be stored for each source:
• Analogue/digital input mode (see page 14)
• Input attenuator mode (see page 20)
• Balance (see page 20)
• Bass boost (see page 21)
• Tone adjustment (see page 21)
• Subwoofer output level (see page 22)
• Surround mode settings (see pages 33, 37)
Theatre Surround settings (see pages 35, 38)
DAP mode settings (see pages 36, 39)
Note:
If the source is FM or AM, you can assign a different setting for
each band.
For recording
You can record sounds of any source playing through the unit to
the VCR or the cassette deck.
While recording, you can listen to the selected sound source at
whatever sound level you like without affecting the sound levels
of the recording.
Note:
Sound adjustments (see page 20) and DSP modes (see page 32)
cannot affect the recording.
Signal and speaker indicators on the display
The following signal indicators light up —:
L:•When digital input is selected: Lights up when the
left channel signal comes in.
• When analog input is selected: Always lights up.
R:•When digital input is selected: Lights up when the
right channel signal comes in.
• When analog input is selected: Always lights up.
C:Lights up when the center channel signal comes in.
LS : Lights up when the left rear channel signal comes in.
RS : Lights up when the right rear channel signal comes in.
S:Lights up when the monaural rear channel signal comes in.
LFE: Lights up when the LFE channel signal comes in.
The speaker indicators light up as follows:
• The subwoofer speaker indicator (
SUBWFR) lights up when
“SUBWFR” is set to “YES” (see page 15).
• The other speaker indicators light up only when the
corresponding speaker is activated AND when the
corresponding speaker is required for the DSP mode currently
selected.
ANALOG
PRO LOGIC
SUBWFR LFE
SLEEP
DGTL AUTO
INPUT ATT
DSP
LCR
LS S RS
LPCM
DOLBY D
DTS
LFE
LCR
LS S RS
SUBWFR
LCR
LS RS
Activating TV Direct
TV Direct is enable you to use this unit as an AV selector while the
unit is not turned on.
When TV Direct is activated, the pictures and sounds go from the
video components such as DVD player to the TV through this unit.
In this case, you can use the video components and the TV as if you
connect them directly.
• This function takes effect only when the video components and
TV are connected to this unit with SCART cables.
• This function takes effect to the following sources — DVD, STB,
and VCR.
• This unit can be automatically turned on or off, and/or select the
source automatically when you set the TV Direct mode to “AUTO
1” or “AUTO 2.” For details, see “Setting the TV Direct mode”
on page 19.
To activate (or deactivate) TV Direct, follow the procedure below.
1
Press TV DIRECT.
All the indications disappear, then the source
indicator currently selected lights red.
2
Turning on the video component and TV.
3
Press one of the source selecting buttons — DVD,
STB, or VCR.
The indicator corresponding to the selected source lights red.
To cancel TV Direct and turn off the unit, press
(or
AUDIO
on the remote control).
The unit is turned off and the STANDBY lamp lights up.
To cancel TV Direct and turn on the unit, press TV DIRECT on
the unit (or AUDIO
on the remote control).
The unit is turned on and the source indicator currently selected
lights green.
Notes:
• When TV Direct is activated, you cannot enjoy all the sound effects
this unit produces, and use the speakers connected to this unit.
• You can use T-V LINK function between TV and VCR while the TV
Direct is activated.
DVD STB VCR
DVD
TV DIRECT
EN10-19.RX-E100RSL[B]_f 01.3.8, 2:49 PM11