Filter
Top Products
Operating procedure
On the front panel:
Before you start, remember...
There is a time limit in doing the following steps. If the setting
is canceled before you finish, start from step
1 again.
Ex.: When adjusting subwoofer output level.
1 Press ADJUST.
MULTI JOG now works for the sound adjustment.
2 Turn MULTI JOG until the item you want
to adjust appears on the display.
• As you turn MULTI JOG, the adjustment items change as
follows:
3 Press SET.
The current setting for the selected item appears.
4 Turn MULTI JOG to adjust the selected
item.
5 Press SET.
Your adjustment is stored.
6 Repeat steps 2 to 5 to adjust other items
if necessary.
7 Press ADJUST.
The source indication resumes on the display.
Sound adjustments
You can make sound adjustment to your preference after
completing basic setting.
Basic adjustment items
You can adjust the following items. See pages in parentheses
for details.
• You cannot select the items which is not available with the
current setting.
Items To do
SUBWFR LVL*
1
Adjust the subwoofer output level. (36)
FRONT L LVL*
1, 2
Adjust the left front speaker output level.
(36)
FRONT R LVL*
1, 2
Adjust the right front speaker output level.
(36)
CENTER LVL*
1, 2
Adjust the center speaker output level. (36)
SURR L LVL*
1, 2
Adjust the left surround speaker output
level. (36)
SURR R LVL*
1, 2
Adjust the right surround speaker output
level. (36)
S BACK LVL*
1, 2
Adjust the surround back speaker output
level when using a single speaker for the
surround back speaker. (36)
S BACK L LVL*
1, 2
Adjust the left surround back speaker
output level. (36)
S BACK R LVL*
1, 2
Adjust the right surround back speaker
output level. (36)
D EQ 63Hz*
1
D EQ 250Hz*
1
D EQ 1kHz*
1
D EQ 4kHz*
1
D EQ 16kHz*
1
Adjust the equalization pattern of each
band. (36)
BASS BOOST Boost the bass level. (37)
INPUT ATT Attenuate the input level of analog source.
(37)
EFFECT Adjust the effect level. (37)
ROOM SIZE Select the room size for your virtual
listening room. (37)
LIVENESS Select the liveness level for your virtual
listening room. (37)
PANORAMA Add “wraparound” sound effect with
sidewall image. (37)
CENTER WIDTH Adjust the center channel localization
between the center speaker and the left/
right speakers. (38)
DIMENSION Adjust sound localization pattern. (38)
CENTER GAIN Adjust the sound localization of the center
channel. (38)
CENTER TONE Make the center tone soft or sharp. (38)
CENTER ALIGN Align the vertical localization of the center
channel signals. (38)
*
1
You can adjust these items directly from the remote control.
*
2
If you have performed Precise Surround Setup on pages 16
to 18, these settings are not required.
SUBWFR LVL Ô FRONT L LVL Ô FRONT R LVL Ô
CENTER LVL Ô SURR L LVL Ô SURR R LVL Ô
S BACK LVL Ô S BACK L LVL Ô S BACK R LVL Ô
D EQ 63Hz Ô D EQ 250Hz Ô D EQ 1kHz Ô
D EQ 4kHz Ô D EQ 16kHz Ô BASS BOOST Ô
INPUT ATT Ô EFFECT Ô ROOM SIZE Ô
LIVENESS Ô PANORAMA Ô CENTER WIDTH Ô
DIMENSION Ô CENTER GAIN Ô CENTER TONE Ô
CENTER ALIGN Ô (Back to the beginning)
–10 0 +10
1, 7 3, 5 2, 4
NOTE
Some items above are not available in the following cases below:
– When selecting “A MULTI” for the audio input setting (see page 11)
– When multi-channel PCM signals (see page 41) are coming in with
selecting “HDMI” for the audio input setting (see page 11)
35