Filter
Top Products
Page 44
English
Using the Remote Control for Operating JVC’s Audio/Video Components
You can operate JVC’s audio and video components with this receiver’s remote control, since control signals
for JVC components are preset in the remote control.
Notes:
• If you use the buttons on the front panel or the menu function to choose a source, the remote control will
not operate that source. To operate a source with the remote control, the source must be selected using
buttons on the remote control.
• Check to see if its remote control mode selector is set to the correct position.
Normally, set it to the “TV / VCR / TUNER / CD / DVD / VCD” position.
To activate the 10 keys for adjusting the sound, set it to the “SOUND CONTROL” position.
• Refer also to the manuals supplied with your components.
IMPORTANT
To operate JVC’s audio components using this remote control:
• You need to connect JVC audio components through the COMPU LINK-3 (SYNCHRO) jacks
(see page 41) in addition to the connections using cables with RCA pin plugs (see page 8).
• Aim the remote control directly at the remote sensor on the receiver.
Tuner
After pressing FM/AM (with the remote control mode selector set to the “TV / VCR / TUNER / CD / DVD /
VCD” position), you can perform the following operations:
FM/AM: Alternates between FM and AM.
1 — 10, +10: Selects a preset channel number directly.
For channel number 5, press 5. For channel number 15, press +10, then 5. For
channel number 20, press +10, then 10.
FM MODE/MUTING: Changes the FM reception mode.
Sound control section (Amplifier)
With the remote control mode selector set to the “SOUND CONTROL” position, you can perform the
following operations:
SEA MODE: Changes the SEA modes.
DAP MODE: Changes the DAP modes.
SURR MODE: Changes the surround modes.
CNTR +/–: Changes the center speaker output level for the DVD MULTI playback and surround
modes.
REAR•(L) +/–: Changes the left/right rear speaker output level for DAP and surround modes.
Changes the left rear speaker output level for the DVD MULTI playback mode.
(REAR•R) +/–: Changes the right rear speaker output level for the DVD MULTI playback mode.
EFFECT: Changes the effect level for DAP and surround modes.
DELAY: Changes the delay time for surround modes.
TEST: Checks the speaker output level for surround modes.
Note:
After adjusting sounds, set the remote control mode selector to the “TV / VCR / TUNER / CD / DVD / VCD”
position to operate your target source by using 10 keys; otherwise, 10 keys cannot be used for operating your
target source.
O
N
S
C
R
E
E
N
C
O
N
T
R
O
L
RM-SR80U REMOTE CONTROL
CD
DISC
VCD
DISC
VCD
CONTROL
VCR
POWER
TV
POWER
AUDIO
POWER
DVD
MULTI
VIDEO1 VIDEO2
TAPE/VCR
VCR1
TV
SOUND
DVD
TEST
(REAR R)
REAR (L)
SEA MODE DAP MODE SURR MODE
FM/AM PHONOCD
546
213
87
/P
9
0
+10
10
TV / VCR / TUNER
/ CD / DVD / VCD
MENU
EXIT
MENU
SET
TAPE VCR
CONTROL
VOLUME
CHANNEL
MUTING
FF / ¢
NEXT /
PLAY
SELECT /
STOP
/ REC
TV/VIDEO
TV VOLUME
PAUSE
4 / REW
PREV /
CNTRDELAY
MENU
ENTER
EFFECT
SOUND
CONTROL
FM MODE/MUTINGRETURN
EN44-52.RX-80P[UF]/f 98.8.31, 1:53 PM44