Filter
Top Products
145
GAudioH
Symptom Cause/Solution Page
Audio is not output. •Check the connections for all devices.
•Check the speaker connections and configurations.
•Check whether the audio device power is turned on.
•Adjust the master volume.
•Cancel the mute mode.
•Select a suitable input source.
•Select a suitable input mode.
•Disconnect the headphones. No sound is output from the speakers
or the PRE OUT connectors when headphones are connected.
C3,8,
10,11,12,13,
14,15,16,17,
18,19
C6,61,
62,64,65,66
–
29, 82
29, 82
28, 82
93
127
No sound is
produced from
surround speaker.
•Check if the surround speakers are connected to the SURROUND
terminals.
–
No sound is
produced from
surround back
speaker.
•Check if “Amp Assign” is set appropriately in order to output
audio from the surround back speakers.
•Set “Speaker Config.” – “Surr.Back” on the menu to something
other than “None”.
•Set “Surround Parameters” – “Surround Back” on the menu to
something other than “OFF”.
•Set the surround mode to something other than “STEREO” and
“VIRTUAL“.
104
105
98
53
No sound is
produced from front
height speaker.
•Set “Surround Parameters” – “PLgz Height” on the menu to
“ON”.
•Check if “Amp Assign” is set appropriately in order to output
audio from the front height speakers.
•Set “Speaker Config.” – “Front Height” on the menu to something
other than “None”.
98
104
105
No sound is
produced from
subwoofer.
•Check the subwoofer connections.
•Turn on the subwoofer’s power.
•Set “Speaker Config.” – “Subwoofer” on the menu to “Yes”.
•If “Front” and “Center” for “Speaker Config.” are set to “Large”,
and “Subwoofer Mode” is set to “LFE”, no sound may be output
from the subwoofers, depending on the input signal or selected
surround mode.
C6,61,
62,64,65,66
–
104
104, 105
Symptom Cause/Solution Page
DTS sound is not
output.
•Set “Decode Mode” on the menu to “Auto” or “DTS”.
93
Dolby TrueHD, DTS-
HD, Dolby Digital
Plus audio is not
output.
•Make HDMI connections.
8
Dolby PLg mode or
DTS NEO:6 mode
cannot be selected.
•Check that “Speaker Config.” – “Center” or “Surround” is set
to other than “None”. If the speaker system is 2.0/2.1ch, this
surround mode cannot be selected.
•When headphones are used, Dolby PLg or DTS NEO:6 cannot be
selected.
104
–
Audyssey DSX™
cannot be selected.
•Check that “Speaker Config.” – “Front Height” or “Front Wide” is
set to other than “None”.
•Check that “Speaker Config.” – “Center” is set to other than
“None”.
•Switch the surround mode to STANDARD.
•When headphones are used, Audyssey DSX™ cannot be selected.
105
104
53
–
Audyssey MultEQ
®
XT, Audyssey
Dynamic EQ
®
and
Audyssey Dynamic
Volume
®
cannot be
selected.
•Switch the surround mode to other than “DIRECT” or “PURE
DIRECT”.
•When headphones are used, MultEQ
®
XT, Dynamic EQ
®
and
Dynamic Volume
®
cannot be selected.
53
–
Dynamic EQ
®
and
Dynamic Volume
®
cannot be selected.
•Run Audyssey
®
Auto Setup.
21, 67
RESTORER cannot
be selected.
•Check that an analog signal or PCM signal (fs=44.1/48 kHz) is
input. For playback of multichannel signals such as Dolby Digital
or DTS surround, RESTORER cannot be used.
•Switch the surround mode to other than “DIRECT” or “PURE
DIRECT”.
102
53
Basic version
Advanced version
InformationInformation