Denon AVR-3312 Stereo Receiver User Manual


 
100
AUDIO/VIDEO ADJUST
n Audyssey Settings
Default settings are underlined.
Set Audyssey MultEQ
®
XT, Audyssey Dynamic EQ
®
and Audyssey Dynamic Volume
®
. These can be
selected after Audyssey
®
Auto Setup has been performed. For additional information on Audyssey
technology, please see page141.
NOTE
•If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup,
you may not be able to select Dynamic EQ
®
/Dynamic Volume
®
.
In this case, either perform Audyssey
®
Auto Setup over again or perform “Restore” (vpage27) to
return to the settings after Audyssey
®
Auto Setup was run.
•When HD Audio for which the sampling frequency exceeds 96 kHz is played back, the “Audyssey
Settings” cannot be set.
Setting items Setting details
MultEQ
®
XT
MultEQ
®
XT corrects
both time and frequency
response problems in the
listening area based on
Audyssey
®
Auto Setup
calibration. We recommend
“Audyssey”.
MultEQ
®
XT is the
prerequisite function for
Dynamic EQ
®
and Dynamic
Volume
®
.
Audyssey : Optimize the frequency response of all speakers.
Audyssey Byp.L/R : Optimize frequency response of speakers except
front L and R speakers.
Audyssey Flat : Optimize frequency response of all speakers to flat
response.
Manual : Apply frequency response set with “Manual EQ” (vpage101).
OFF : Turn “MultEQ
®
XT” equalizer off.
•“Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” can be selected
after Audyssey
®
Auto Setup has been performed. “Audyssey” is
automatically selected after performing Audyssey
®
Auto Setup. When
“Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is selected,
illuminates.
•After running Audyssey
®
Auto Setup, if the Speaker Configuration,
Distance, Channel Level, and Crossover Frequency have changed
without increasing the number of speakers measured, only
illuminates.
NOTE
•“MultEQ
®
XT” and “Manual” cannot be selected when “EQ Customize”
is set to “Not Used” (vpage109).
•When using headphones, “MultEQ
®
XT” is automatically set to “OFF”.
“MultEQ
®
XT”, “Dynamic EQ
®
” and “Dynamic Volume
®
” settings are stored for each input source.
Setting items Setting details
Dynamic EQ
®
Solve the problem of
deteriorating sound quality
as volume is decreased
by taking into account
human perception and
room acoustics. Works with
MultEQ
®
XT.
ON : Use Dynamic EQ
®
.
OFF : Do not use Dynamic EQ
®
.
or is displayed when set to “ON”.
Reference Level Offset
Audyssey Dynamic EQ
®
is
referenced to the standard
film mix level. It makes
adjustments to maintain
the reference response
and surround envelopment
when the volume is turned
down from 0 dB. However,
film reference level is not
always used in music or
other non-film content.
Dynamic EQ
®
Reference
Level Offset provides three
offsets from the film level
reference (5 dB, 10 dB, and
15 dB) that can be selected
when the mix level of the
content is not within the
standard.
0dB (Film Ref) : This is the default setting and should be used when
listening to movies.
5dB : Select this setting for content that has a very wide dynamic range,
such as classical music.
10dB : Select this setting for jazz or other music that has a wider dynamic
range. This setting should also be selected for TV content as that is usually
mixed at 10 dB below film reference.
15dB : Select this setting for pop/rock music or other program material
that is mixed at very high listening levels and has a compressed dynamic
range.
Setting is enabled when “Dynamic EQ
®
” is “ON” (vpage100).
Dynamic Volume
®
Solve the problem of large
variations in volume level
between TV, movies and
other content (between
quiet passages and
loud passages, etc.) by
automatically adjusting to
the user’s preferred volume
setting.
Midnight : Most adjustment to loudest and softest sounds.
Evening : Medium adjustment to loudest and softest sound.
Day : Least adjustment to loudest and softest sounds.
OFF : Do not use “Dynamic Volume
®
”.
•
is displayed when set to “Midnight”, “Evening” or “Day”.
•If “Dynamic Volume
®
” is set to “Yes” in Auto Setup (vpage25),
the setting is automatically changed to “Evening”.
Basic version
Advanced version
Information
Advanced version
BD