Filter
Top Products
31
CTL/EXP
ACCEL/CTL, EXP SW, SUB CTL 1, SUB
CTL 2
Here’s how to assign the parameters that will be controlled by the ACCEL/
CTL, EXP SW, SUB CTL 1 and SUB CTL 2 pedals.
Parameter Value Explanation
FUNC
OFF No assignment.
ACCEL Switches the ACCEL eect on and o.
P.LOOP ON/OFF Switches the PHRASE LOOP on and o.
P.LOOP REC/PLY Records/plays back the phrase.
P.LOOP STP/PLY Stops/plays back the phrase.
P.LOOP CLEAR Clears the phrase
DIV CH SELECT Switches between Preamp channel A and B.
OD/DS SOLO Switches the OD/DS SOLO on and o.
A/B SOLO Switches the Preamp SOLO on and o.
A&B SOLO
Switches the preamp SOLO, for both
channel A and B, on and o.
If one of the two channels is o, both will be
turned on.
COMP Switches the COMP on and o.
OD/DS Switches the OD/DS on and o.
PREAMP Switches the PREAMP/SPEAKER on and o.
EQ Switches the EQ on and o.
FX1 Switches the FX1 on and o.
FX2 Switches the FX2 on and o.
DELAY Switches the DELAY on and o.
CHORUS Switches the CHORUS on and o.
REVERB Switches the REVERB on and o.
PEDAL FX Switches the Pedal FX on and o.
SEND/RETURN Switches the SEND/RETURN on and o.
AMP CTL Switches the Amp Control on and o.
TUNER Switches the TUNER/BYPASS on and o.
MANUAL MODE Switches the MANUAL MODE on and o.
BPM TAP *1 Used for tap input of the MASTER BPM.
DELAY TAP *1 Used for tap input of the delay time.
MIDI START
Controls the Start/Stop of external MIDI
devices (such as sequencers).
MMC PLAY
Controls the Play/Stop of external MIDI
devices (such as hard disk recorders).
LEVEL +10 *1
Increases the patch volume level by 10
units.
LEVEL +20 *1
Increases the patch volume level by 20
units.
LEVEL -10 *1
Decreases the patch volume level by 10
units.
LEVEL -20 *1
Decreases the patch volume level by 20
units.
NUMBER INC *1
Switches to the next higher patch number
in the same bank as the currently selected
patch.
NUMBER DEC *1
Switches to the next lower patch number
in the same bank as the currently selected
patch.
BANK INC *1 Switches to the next higher bank number.
BANK DEC *1 Switches to the next lower bank number.
LED ON/OFF
Lights/extinguishes the pedal’s LED
indicator.
* This is shown only when ACCEL/CTL pedal
is selected.
* This is shown only if PERFORMANCE (p. 28)
is set to PATCH.
*1 The function will activate as soon as you press the pedal, regardless of
whether the SOURCE MODE parameter is MOMENT or TOGGLE.
Parameter Value Explanation
MIN
OFF, ON
(or STOP, START)
This sets the value for times when the
switch is O.
MAX
OFF, ON
(or STOP, START)
This sets the value for times when the
switch is On.
SOURCE
MODE
This sets the behavior of the value each time the switch is
operation.
MOMENT
The normal state is O (minimum value),
with the switch On (maximum value) only
while the footswitch is depressed.
TOGGLE
The setting is toggled On (maximum value)
or O (minimum value) with each press of
the footswitch.
EXP, SUB EXP
Here’s how to assign the parameters that will be controlled by the GT-100’s
[EXP] pedal, and by an expression pedal (such as the separately available
EV-5) connected to the SUB CTL 1, 2/SUB EXP jack.
Parameter Value Explanation
FUNC
OFF No assignment.
FOOT VOLUME Foot volume will be assigned.
PEDAL BEND Pedal bend will be assigned.
WAH Wah will be assigned.
PB/FV Pedal bend and foot volume will be assigned.
WAH/FV Wah and foot volume will be assigned.
PATCH LEVEL
Patch level will be assigned.
* This is shown only if PERFORMANCE (p. 28) is set
to SYSTEM.
PATCH LEVEL
MIN
0–200
Species the minimum value.
* This is shown only if FUNC is set to PATCH
LEVEL.
PATCH LEVEL
MAX
0–200
Species the maximum value.
* This is shown only if FUNC is set to Patch Level.
* Only FOOT VOLUME can be assigned to SUB EXP (external expression
pedal). If you want to assign a function other than FOOT VOLUME, use
Assign.