Filter
Top Products
EFFECT
11
LIMITER
The limiter attenuates loud input levels to prevent distortion.
Parameter Value Explanation
TYPE
Selects the limiter type.
BOSS LIMITER This selects a stereo limiter.
RACK 160D This models a dbx 160X.
VTG RACK U This models a UREI 1178.
THRESH 0–100
Adjust this as appropriate for the input
signal from your guitar. When the input
signal level exceeds this threshold level,
limiting will be applied.
RATIO 1:1–INF:1
This selects the compression ratio used with
signals in excess of the threshold level.
LEVEL 0–100 Adjusts the volume.
ATTACK 0–100
Adjusts the strength of the picking attack
when the strings are played. Higher values
result in s sharper attack, creating a more
clearly dened sound.
RELEASE 0–100 Adjusts the release time.
SUB OD/DS
This eect distorts the sound to create long sustain.
Parameter Value Explanation
TYPE
Refer to “OD/DS TYPE” (p. 5)
* “CUSTOM” is not available.
DRIVE 0–120 Adjusts the depth of distortion.
TONE -50–+50 Adjusts the tone.
EFFECT LEVEL 0–100 Adjusts the volume of the OD/DS sound.
BOTTOM -50–+50
Adjusts the tone for the low frequency range.
Turning this to the left (counterclockwise)
produces a sound with the low end cut;
turning it to the right boosts the low end in
the sound.
DIRECT MIX 0–100 Adjusts the volume of the direct sound.
SOLO SW OFF, ON The tone to one suitable for solos.
SOLO LEVEL 0–100
Adjusts the volume level when the Solo Sw
is ON.
GRAPHIC EQ
This adjusts the tone as a equalizer. You can adjust the sound quality in ten bands.
Parameter Value
31 Hz
-20–+20 dB
62 Hz
125 Hz
250 Hz
500 Hz
1 kHz
2 kHz
4 kHz
8 kHz
16 kHz
LEVEL -20–+20 dB
PARAMETRIC EQ
Adjusts the tonal quality. You can adjust the sound quality in four bands.
Parameter Value Explanation
LOW GAIN -20–+20 dB Adjusts the low frequency range tone.
HIGH GAIN -20–+20 dB Adjusts the high frequency range tone.
LEVEL -20–+20 dB
Adjusts the overall volume level of the
equalizer.
LOW-MID
FREQ
20 Hz–10.0 kHz
Species the center of the frequency range
that will be adjusted by the LOW-MID GAIN.
LOW-MID Q 0.5–16
Adjusts the width of the area aected by the
EQ centered at the LOW-MID FREQ. Higher
values will narrow the area.
LOW-MID
GAIN
-20–+20 dB
Adjusts the low-middle frequency range
tone.
HIGH-MID
FREQ
20 Hz–10.0 kHz
Species the center of the frequency range
that will be adjusted by the HIGH-MID GAIN.
HIGH-MID Q 0.5–16
Adjusts the width of the area aected by the
EQ centered at the HIGH-MID FREQ. Higher
values will narrow the area.
HIGH-MID
GAIN
-20–+20 dB
Adjusts the low-middle frequency range
tone.
LOW CUT FLAT, 20 Hz–800 Hz
This sets the frequency at which the low
cut lter begins to take eect. When FLAT is
selected, the low cut lter will have no eect.
HIGH CUT
630 Hz–12.5 kHz,
FLAT
This sets the frequency at which the high
cut lter begins to take eect. When FLAT
is selected, the high cut lter will have no
eect.
TONE MODIFY
This changes the tone of the connected guitar.
Parameter Value Explanation
TYPE
Selects the type of tone modication.
FAT Fat tone with boosted mid range.
PRES (PRESENCE) Bright tone with boosted high-mid range.
MILD Mild tone with the high end cut back.
TIGHT Tone with the low frequencies cut.
ENHANC (ENHANCE) Tone with the high frequencies boosted.
RESO 1–3
(RESONATOR 1–3)
This produces a tone with greater power
and punch by adding resonance in the
low-frequency range and midrange.
LOW -50–+50
Adjusts the tone for the low frequency
range.
HIGH -50–+50
Adjusts the tone for the High frequency
range.
LEVEL 0–100 Adjusts the volume of the eect sound.
RESO 0–100
This adjusts the strength of the low-end and
midrange resonance when TYPE is set to
RESO 1, 2, or 3.