Filter
Top Products
PAGE
11
Community XLT / XLTE Series Owner’s Manual
4 COMMUNITY XLT™ AND XLTE™ SERIES GENERAL DESCRIPTION
The XLT loudspeaker systems have features and functions designed primarily for portable applications. The XLTE
systems are suitable for both heavier-duty portable use and for permanent installation. From the smallest to the
largest model, these loudspeakers represent Community’s commitment to meeting the audio requirements for sound
reinforcement with performance, quality, and reliability at affordable prices.
4.1 ABBREVIATED OPERATING INSTRUCTIONS
This General Description Chapter about the features and functions can serve as abbreviated operating instructions on
how to use your new product. More detailed information can be found in the chapters that follow.
4.2 MODELS (See Appendix for details about XLT41E and XLT48E model variations)
The full-range loudspeakers reproduce all but the very deepest bass frequencies. The HF drivers (and MF driver in
the 46) are horn-loaded for maximum efficiency and for directional control of the sound. For additional bass output
at the extreme low end of the audio frequency range, model 51 or 55 subwoofers can be used with the full-range
loudspeakers to produce added depth and impact. The 51 and 55 subwoofers are ported (bass reflex) designs,
engineered to match the enclosure sizes and acoustic performance of the full-range loudspeakers.
MODEL TYPE LOW FREQUENCY MID FREQUENCY
HIGH FREQUENCY
2
41 2-way floor monitor / PA (1) 12 in. / 305 mm N/A (1) 1 in. / 25 mm Titanium
42
1
2-way full-range (1) 12 in. / 305 mm N/A (1) 1 in. / 25 mm Titanium
43 2-way full-range (1) 15 in. / 381 mm N/A (1) 1 in. / 25 mm Titanium
46 3-way full-range (1) 15 in. / 381 mm (1) 6.5 in. / 165 mm) (1) 1 in. / 25 mm Titanium
47 2-way full-range (2) 15 in. / 381 mm N/A (1) 1 in. / 25 mm Titanium
48 2-way floor monitor (1) 15 in. / 381 mm N/A (1) 1 in. / 25 mm Titanium
51 Ported subwoofer (1) 15 in. / 381 mm N/A N/A
55 Ported subwoofer (2) 15 in. / 381 mm N/A N/A
1
This model is only part of the XLTE Series.
2
2 in. / 51 mm diameter diaphragm , 1 in. / 25 mm exit driver on a 1 in. / 25 mm entrance horn
Table 2: Product Listing
4.3 DRIVERS
All systems use proprietary drivers built to precise Community designs and specifications using the latest in materials
technology and design philosophy.
4.3.1 High Frequency Driver
The high frequency driver for all full-range systems is a 1 in. / 25 mm exit compression driver with a 2 in. / 51 mm
diameter titanium diaphragm. It provides high power handling capabilities while retaining the small diaphragm area
necessary to reproduce the small wavelengths of the highest audible frequencies.
4.3.2 Mid Frequency Driver (46 models only)
The midrange driver in the 46 models is a Ferrofluid cooled 6.5 in. / 165 mm horn loaded cone driver. Its long
excursion, low compression ratio design results in exceptionally low distortion. The large magnetic structure
provides high sensitivity along with high power handling that extends well below its 500 Hz crossover point.
4.3.3 Low Frequency Drivers
The low frequency drivers in all models are high sensitivity cone-type transducers. Their characteristics vary
depending on the particular loudspeaker model. Large magnetic structures, edge-wound voice coils, and high
stiffness-to-mass cones enhance power handling and clean reproduction. The enclosures are ported designs (also
called bass-reflex or vented) to improve low frequency efficiency and extend the low frequency response.