Filter
Top Products
44-EN
Edit Code:
Change the passcode.
1 Input the old passcode as steps 1 to 4 in “How to input
passcode?”.
After the old passcode is entered, the new passcode input
screen will be displayed.
2 Input the new passcode as steps 1 to 4 in “How to input
passcode?”.
A confirm screen will be displayed and the new passcode must
be entered again for confirmation.
When the passcode is changed successfully, the unit will
display Code Saved.
Note
• Keep a note of the numbers somewhere safe in case you should
forget it.
You can check the signal strength through this setting item.
Setting item: Signal Indicator
Setting content:
Signal Indicator
Signal Indicator:
This menu item displays the SiriusXM signal strength as Strong,
Good, Weak or No Signal.
Note
• If the Signal Indicator reports Weak or No Signal and your vehicle is
parked outside with no obstructions to the southern sky, then your
SiriusXM antenna may not be properly installed or may have become
damaged.
Checking the SiriusXM Radio ID Number
To subscribe to the SiriusXM Satellite Radio service, it is necessary to
locate and identify the Radio ID of your SiriusXM Tuner. The Radio ID
contains 8 characters and can be found on the bottom of your SiriusXM
Tuner or can be displayed on when selecting Channel 0 by following the
steps below:
1
While in the Satellite Radio Mode, press or to
select channel “0”.
The unit displays “RADIO ID” and ID number at the same time.
Note
• The Radio ID does not include the letters I, O, S or F.
2
To cancel the ID number display, select a channel other
than “0”.
Storing Channel Presets
1
Press BAND to select the desired band you want to store
the preset in.
There are 3 Satellite Radio Preset bands.
Each press of BAND changes the band: SiriusXM1 SiriusXM2
SiriusXM3 SiriusXM1
2
Tune to the desired channel, and then press and hold (for
at least 2 seconds) one of the preset buttons (1 through 6)
to store the channel.
The display then shows the stored Band and preset number (for
example, SiriusXM1-3 is shown when preset 3 of BAND1 is
selected).
3
Repeat the procedure to store up to 5 other channels onto
the same band.
Notes
• A total of 18 channels can be stored in the preset memory, 6 Channels
for each band (SiriusXM1, SiriusXM2 and SiriusXM3).
• If you store a new channel into a preset which already has a channel
assigned, the current channel will be cleared and replaced with the new
one.
Tuning Channels using Presets
1
Press BAND to select the desired band of Presets you wish
to access.
2
Press the preset buttons (1 through 6) that has your
desired Satellite Radio channel stored in memory.
Storing the desired Artist and Song Alerts
While listening to SiriusXM Satellite Radio, you can be alerted when
your favorite songs or artists are playing on other channels. An
interruption Alert will be displayed when a matching artist or song is
found on another channel. For receiving interruption Alert information,
refer to “Receiving and Tuning to an Alert” on page 45.
1
Press and hold ENTER/OPTION for at least 2 seconds
when a Song or the song of an Artist you want to store is
playing.
The Option mode is activated.
2
Turn the Rotary encoder to select Alert Memory, and then
press ENTER.
3
Turn the Rotary encoder to choose Save Artist? or Save
Song? (when available), and then press ENTER.
Note
• If both the artist name and song title are not available to save, Artist/
Songe will be displayed.
4
The new alert was stored in memory.
An “Artist/Song Saved” pop-up screen is followed by an “X
U(sed)/Y E(mpty)”.
X is the total number of song titles or artist names stored in
memory, and Y is the total number of memory locations still
available for storage.
Notes
• If you try to store when the memory is full, “Memory Full” is displayed
followed by “Replace/Cancel”. If you want to replace an existing alert
item, select “Replace” by turning Rotary encoder, and then press
ENTER, the existing alert list stored in memory is displayed. Select
one of the stored alerts using the Rotary encoder. To replace the
selected alert, press ENTER and an “Artist/Song Saved” pop-up
screen is followed by an “X U(sed)/Y E(mpty)”.
• You can manage the stored Alert memory setting on Setup mode, for
details, refer to “Managing Artist and Song Alerts” on page 43.
• If no operation is performed for 60 seconds, the setting mode is
canceled.
Confirming the strength of the SiriusXM
signal