Filter
Top Products
19-EN
5
Repeat steps 3 to 4 to complete the setting of other bands.
You can change the unit, (cm or inch) of time correction.
Setting item: TCR Parameter
Setting contents:
cm (Initial setting) / inch
cm:
Time correction value is in centimetres.
inch:
Time correction value is in inches.
Before performing the following procedures, refer to “About Time
Correction” on page 20.
1
After selecting T.Correction from the Audio Setup mode,
turn the Rotary encoder to select a speaker to be
adjusted, and then press ENTER.
F-L
*1
F-R
*2
R-L
*3
R-R
*4
SW-L SW-R
*1 Front-L
*2 Front -R
*3 Rear-L
*4 Rear-R
2
Turn the Rotary encoder to adjust the distance of the
selected speaker, and then press ENTER.
0.0 cm to 336.6 cm (3.4 cm/step)
0.0 inch to 132.7 inch (1.3 inch/step)
Note
• The total adjustment distance for all speakers should be less than 510
centimeters (201 inches).
3
Repeat steps 1 and 2 to set another speaker.
By setting these values to make its sound reach the listening
position at the same time as the sound of other speakers.
This function allows you to change the sound field easily.
There are three modes to choose from. For details, refer to the table
below.
Before performing the following procedures, refer to “About the
Crossover” on page21.
1
After selecting X-Over from the Audio Setup mode, turn
the Rotary encoder to select the desired channel, then
press ENTER.
2
Turn the Rotary encoder to select the desired frequency
within the selected channel, then press ENTER.
3
Repeat step 2 to adjust the Slope and Level within the
selected channel.
Adjusting the Channel (Ch.)
Setting contents:
Front (HPF) / Rear (HPF) / SUBW (LPF)
Selecting the Cut-Off Frequency (Freq.)
Setting contents:
20 / 25 / 31.5 / 40 / 50 / 63 / 80 (Initial setting) / 100 / 125 /
160 / 200 (Hz)
Adjusting the Slope
Setting contents:
Flat (Initial setting) / 6 / 12 / 18 / 24 dB/oct.
Adjusting the Level (Lev.)
Setting contents:
−12 to 0 (dB) (Initial setting: 0)
4
Repeat steps 1 to 2 to make adjustment to the other
channels.
The Parametric EQ/T.Correction and X-Over settings can be stored in
the preset memory.
1
The Parametric EQ/T.Correction/X-OVER settings can be
stored in any one of the preset buttons (1 through 6).
After completing any adjustment for Parametric EQ/
T.Correction/X-OVER (e.g. BAND), press and hold the
desired preset button for at least 2 seconds.
2
Turn the Rotary encoder to select Protect YES/NO, and
then press ENTER to store the adjusted contents.
Protect NO Protect YES (Initial setting)
Notes
• If Protect YES is selected, the adjusted contents are protected and stored
into the preset buttons. When you want to store the parameter into a
protected preset button, “Replace NO/YES” can be selected.
If Protect NO is selected, the preset is stored.
• While perform this operation, all adjusted contents of Parametric EQ/
T.Correction and X-Over will be stored in the preset buttons.
• The stored contents are not deleted even when resetting the unit or
disconnecting the battery.
• The stored contents can be recalled by performing operation (refer to
“Recalling the Stored Parametric EQ/T.Correction/X-Over Settings” on
page20).
Setting the Time Correction Unit
(TCR Parameter)
Adjusting the Time Correction
(T.Correction)
Adjusting SPATIAL
Mode Effect
OFF
(Initial setting)
No effect is applied.
OFF status
Front Wide
Creates the effect of widening the front sound
field by delaying the sound of the front
speakers.
Rear Wide
Creates the effect of making the front sound
image clear and far by delaying the sound of
the rear speakers.
Adjusting the Crossover Settings (X-Over)
Storing the Parametric EQ/T.Correction/
X-Over Settings