Filter
Top Products
\
SETTING THE CLOCK
SETTING THE TIMER
]
~
\
\,
■
1
~
i
j
[
1,2,3
,,
k
8
2,4
3
a
t
1,2
,
2,3
6
1
Press the CLOCK button on the remote control,
The unit can be turned on at a specified time every day with the
built-in timer.
and press the I I SET button within 4 seconds.
@~~p~~,a@yf~:E~gy*~g.#@&MBap,s@z~*~bY&.-
,,,.q & i%.:L.p&k’-*’@&.,E@Bwe=,e=,Tb
.. %....-
‘$’-!-’whw%~,%~,-,,,: ,“, *M” -“”%=9+
=-,k,.b..@?M&$@B-
Preparation
, .,.,,,~~,.-,&.~,,,=,,.u,=~,g~&s
#$~A~B&$Q~.’z~gl~~,;p_ :::.:“jV!j@Lgq@@.F=%%@&
Make sure the clock is set correctly.
fu%~i~*g#gE8i$q&**$, , , , , ...... l.- .....!$~$~~~@J*d#m*
zae.::bE;3:6@@’:Ez:td8:kiii!!
,9,,, !“?~iPB~’$#JJ$@#**#l$*$nJ,kik* ~~%
@’B18;,,~~;@-hw&i?
mlip,p~g$p~
$@Fqp&#~ib& ~~~,
Use the remote control.
. ~, ,,,,,~jg~~g~t ~~~B~~~,~ M!. ‘@m,*.=
,,,,8,,eq
.,..,,.$~,z. “’~”#3
7 Press the TIMER button once to display 0, and
2 Press the 4+ DOWN or
➤F UP button to
press the II SET button within 4 seconds.
designate the hour, and press the 11SET button.
O
is displayed, and the hour flashes.
The hour stops flashing and the minute starts flashing.
3 Press the << DOWN or ➤> UP button to
I
designate the minute, and press the II SET
button.
The minute stops flashing on the display and the clock starts
from 00 seconds.
m
To display the current time
If you press the II SET button after 4 seconds, another
Press the CLOCK button on the remote control. The time is
operation may start.
displayed for 4 seconds.
However, the time cannot be displayed during recording.
2 Designate the hour of the timer-on time by
pressing the
l<< DOWN or WI UP button, and
TO switch to the 24-hour standard.
press the 11 SET button. Repeat to designate the
Press the CLOCK button on the remote control and then press
minute of the timer-on time.
the ■ button within 4 seconds.
Repeat the same procedure to restore the 12-hour standard.
If the clock display flashes .
This is caused by a power interruption; The current time needs
to be reset.
After you designate the timer-on time, one of the source name
If power is interrupted for more than approximately 24 hours,
flashes on the display for 4 seconds.
all settings stored in memory after purchase need to be reset.
3 Within 4 seconds, press one of the function
buttons to select a source.
The selected source name flashes for4 seconds. At this time,
the selected function button does not light up,
● If this step is not completed within 4 seconds, repeat from
step 1.-
● If the TUNER button is pressed, the band cannot deselected’
in this step.
4
Within 4 seconds, select the duration for the
timer-activated period with the 1<4 DOWN or WI