Filter
Top Products
User's Manual
61
APPENDIX
Optional VIA!migo iPod Dock
1. Remote Input
This connection is not required
for connecting to the TGR-401
(see #5 below). It allows you to
send remote control commands
from 3rd party controllers to the
VIA!migo dock via the rear panel.
2. Video Outputs
Connect either of these outputs
to a video input of the TGR-401.
Composite video 4 and S-Video
4 are the default video inputs for
MP3.
You will be able to see the menu
system and "now playing" infor-
mation from the iPod on your TV
monitor, and see movies (in full
color) if you are using a video
iPod.
If you use the composite output,
the video will be available to Zone
2 as well as the Main Zone. The
TGR-401 will upconvert to com-
ponent.
Even if you do not have a video
iPod, you must make the video
connection, or it will not be easy
to navigate through your song lists
and select songs.
3. L/R Audio Outputs
Connect these analog audio
outputs to the analog L/R inputs
of the TGR-401. You will be able
to hear the audio output from your
iPod.
DATA I/O10V DCR
AUDIO
LVIDEOS-VIDEOREMOTE IN
2 4 51 2 3 3
Analog input 4 is the default input
for MP3, and must be used for
feedback if you are using the
optioanl Olé-2SF touchpad.
4. DC Input
The supplied power supply con-
nects here. Do not use any other
power supply. The VIA!migo will
charge the iPod.
5. Data I/O
This connector is used with
standard Cat-5 Ethernet cable to
join the VIA!migo to the VIA!migo
connector on the TGR-401.
The connection allows iPod
metadata (such as song title, artist
name, and album) to pass to the
TGR-401 for display on the front
panel, on-screen, or in the op-
tional Olé-2SF touchpads.
6. IR Receiver
This allows you to use the remote
control to operate your iPod.
The remote should rst be set
to MP3, then it can be used to
search through the iPod menus,
select songs and play them (see
next page).
7. Power LED
This will light when the VIA!migo
is turned on. Use the remote
control (in MP3 mode) to turn it on
and off remotely.
6 7
Default settings
This OSD menu shows the default
settings of the MP3 input, and is
found in the Main Menu/Setup/In-
puts menu.
This menu shows that if MP3 is
selected as an input, the video
is expected to come into input 4
(S-video or composite), and the
audio into analog audio input 4.
The audio is 2-channel analog, so
the last 4 selections in this table
for digital audio are not used in
this application.
If the VIA!migo is connected to
inputs other than 4, use this menu
to select the inputs you are using.
Once the VIA!migo has been
connected to the TGR-401, see
the operation details on the next
page.
INPUT 4 CHOICES
ZONES M/Z2 OFF, MAIN, ZONE 2, M/Z2
NAME MP3 (UP TO 10 LETTER, NUMS AND
SPECIAL CHARACTERS
GAIN TRIM 0.0 DB -20 TO + 20 DB
ANA AUDIO 4 N, 1, 2, 3, 4, 8 CH (N = NO
ASSIGN)
DIGITAL COAX4 N, COAX 1-4, OPT 1-4
COMPOSITE 4 N, 1-4
S VIDEO 4 N, 1-4
COMPONENT VIDEO N N, 1-3
HDMI N N, 1-3
VIDEO DELAY 0 MS 0-180 MS IN 5 MS STEPS
AUTODET ANA N N/Y
AUTODET DIG AUD N N/Y
AUTODET CV N N/Y
AUTODET SV N N/Y
AUTODET COMPON N N/Y
2-CH ANALOG LAST LAST, STEREO, MONO, PARTY,
PLIIX MUSIC, PLIIX MOVIE,
PLIIX GAME, PLIIX MATRIX,
NEO:6 MUSIC, NEO:6 CINEMA,
JAZZCLUB, SRC DIRECT
2-CH DIGITAL LAST LAST, STEREO, MONO, PARTY,
PLIIX MUSIC, PLIIX MOVIE,
PLIIX GAME, PLIIX MATRIX,
NEO:6 MUSIC, NEO:6 CINEMA,
JAZZCLUB,
DOLBY LAST LAST, DIGITAL, DIGITAL EX,
PLIIX MUSIC, PLIIX MOVIE
DTS LAST LAST, DIGITAL SURROUND,
NEO:6, SUNFIRE
DTS96 LAST LAST, DTS 96/24, NEO:6,
SUNFIRE