Filter
Top Products
Using other functions
08
63
En
Switching the speaker system
If you selected Speaker B in Surround back speaker
setting on page 85, three speaker system settings are
possible using SPEAKERS. If you selected Normal, Front
Bi-Amp or ZONE 2, the button will simply switch your
main speaker system on or off. The options below are for
the Speaker B setting only.
1
•Use
SPEAKERS
on the front panel to select a
speaker system setting.
As mentioned above, if you have selected Normal, the
button will simply switch your main speaker system (A)
on or off.
Press repeatedly to choose a speaker system option:
• SPA – Sound is output from speaker system A and
the same signal is output from the pre-out terminals.
• SPB – Sound is output from the two speakers
connected to speaker system B. Multichannel
sources will not be heard. The same signal is output
from the surround back channel pre-out terminals.
• SPAB – Sound is output from speaker system A (up
to 5 channels, depending on the source), the two
spea
ke
rs in speaker system B, and the subwoofer.
The sound from speaker system B will be the same as
the sound from speaker system A (multichannel
sources will be downmixed to 2 channels).
• SP (off) – No sound is output from the speakers. The
same sound is output from the pre-out terminals
(including from your subwoofer, if connected) as
when selecting speaker system A (above).
Using the MULTI-ZONE controls
The following steps use the front panel controls to adjust
the sub zone volume and select sources. See MULTI-
ZONE remote controls on page 64.
1Press
MULTI-ZONE ON/OFF
on the front panel.
Each press selects a MULTI-ZONE option:
• ZONE 2 ON – Selects your primary (ZONE 2) sub
zone
• ZONE 2&3 ON – Select both sub zones
• ZONE 3 ON – Selects your secondary (ZONE 3) sub
zone
• MULTI ZONE OFF – Switches the MULTI-ZONE
feature off
The MULTI-ZONE indicator lights when the MULTI-ZONE
control has been switched ON.
2Press
MULTI-ZONE CONTROL
on the front panel to
select the sub zone(s) you want.
If you selected ZONE 2&3 ON above, you can toggle
between ZONE 2 and ZONE 3.
•When the receiver is on,
2
make sure that any
operations for the sub zone are done while ZONE and
your selected sub zone(s) show in the display. If this
is not showing, the front panel controls affect the
main zone only.
3Use the
INPUT SELECTOR
dial to select the source
for the zone you have selected.
For example, ZONE 2 CD-R sends the source connected
to the CD-R inputs to the primary (ZONE 2) sub room.
•If you select TUNER, you can use the tuner controls
to select a preset station (see Saving station presets
on page 48 if you’re unsure how to do this).
3
Note
1 • The subwoofer output depends on the settings you made in Manual speaker setup on page 84. However, if SPB is selected above, no sound
is heard from the subwoofer (the LFE channel is not downmixed).
• Depending on the settings in Surround back speaker setting on page 85 output from the surround back pre-out terminals may change.
• All speaker systems (except Speaker B connections) are switched off when headphones are connected.
MASTER
VOLUME
VSX-LX52
VANCED
RROUND
STANDARD
SURROUND
MCACC SETUP MIC
SPEAKERS
HOME THX
USB
CONTROL
MULTI-ZONE
ON
/
OFF
HDMIPQLS PRESET PRESET TUNER EDIT
ENTER
iPod
iPhone
VIDEO
CAMERA
HDMI 4
2If the receiver is in standby, the display is dimmed, and ZONE and your selected sub zone(s) continue to show in the display.
3 The tuner cannot be tuned to more than one station at a time. Therefore, changing the station in one zone also changes the station in the other
zone. Please be careful not to change stations when recording a radio broadcast.
INPUT
SELECTOR
STANDBY/ON
PHONES
BAND TUNE
MASTER
VOLUME
VSX-LX52
MCACC SETUP MIC
SPEAKERS
USB
CONTROL
MULTI-ZONE
ON
/
OFF
HDMIPQLS PRESET PRESET TUNER EDIT
ENTER
iPod
iPhone
VIDEO
CAMERA
HDMI 4
VSX-LX52_SVYXJ.book 63 ページ ２００９年２月２６日 木曜日 午後４時３１分