Filter
Top Products
Using other functions
11
72
En
Reducing the level of an analog signal
The input attenuator lowers the input level of an analog
signal when it’s too strong. You can use this if you find
the that the OVER indicator is lights often, or you can
hear distortion in the sound.
1
• Press
RECEIVER
, then press
A.ATT
to switch the
input attenuator on or off.
Using the sleep timer
The sleep timer switches the receiver into standby after a
specified amount of time so you can fall asleep without
worrying about the receiver being left on all night. Use
the remote control to set the sleep timer.
• Press
RECEIVER
, then press
SLEEP
repeatedly to set
the sleep time.
• You can check the remaining sleep time at any time
by pressing SLEEP once. Pressing repeatedly will
cycle through the sleep options again.
2
Dimming the display
You can choose between four brightness levels for the
front panel display. Note that when selecting sources, the
display automatically brightens for a few seconds.
• Press
RECEIVER
, then press
DIMMER
repeatedly to
change the brightness of the front panel display.
Switching the speaker impedance
We recommend using speakers of 8 Ω with this system,
but it is possible to switch the impedance setting if you
plan to use speakers with a 6 Ω impedance rating. Use
the front panel controls to do this.
• With the receiver in standby, press
STANDBY/
ON
while holding down the
SPEAKERS
button.
Each time you do this, you switch between the
impedance settings:
• Speaker 6 Ω – Use this setting if your speakers are
rated at 6 Ω.
• Speaker 8 Ω – Use this setting if your speakers are
rated at 8 Ω or more.
Checking your system settings
Use the status display screen to check your current
settings for features such as surround back channel
processing and your current MCACC preset.
1 Press
RECEIVER
, then press
STATUS
to check the
system settings.
These appear on the front panel display.
3
The front panel display shows each of the following
settings for three seconds each:
2 When you’re finished, press
STATUS
again to
switch off the display.
Note
1 The attenuator isn’t available with digital sources, or when using the Stream Direct modes.
2 You can also switch off the sleep timer simply by switching off the receiver.
INPUT
123
SLEEPMCACCGENRE
456
A.ATTSBchSR+
789
CLASS
MASTER
VOLUME
CH LEVELD.ACCESS
0
ENTER
A.ATT
9
TV CTRL
MAIN
ZONE 2
AUDIO
DISPLAY
CH
RECEIVERRECEIVER
DIMMER
123
SLEEPMCACC
INPUT
SELECT
GENRE
456
A.ATTSBchSR+
789
CLASSCH LEVELD.ACCESS
0
ENTER
SLEEP
6
TV CTRL
MAIN
ZONE 2
AUDIO
DISPLAY
CH
RECEIVERRECEIVER
30 min
60 min
90 minOff
DIMMER
FM/AM
123
SLEEPMCACC
INPUT
SELECT
GENRE
456
A.ATTSBchSR+
789
iPod USB
DIMMER
3
TV CTRL
MAIN
ZONE 2
DTV/TV
AUDIO
DISPLAY
EON MPX
SIGNAL SEL
CH
RECEIVERRECEIVER
3 If the Pure Direct mode is switched on, some settings above will show OFF, even though they are on.
Input source
↓
Surround Back Processing
↓
MCACC preset
↓
ZONE 2
↓
HDMI Control
THX STATUS PHASE
TV CTRL
DTV/TV
AUDIO
DISPLAY
EON MPX
SIGNAL SEL
CH
RECEIVER
STATUS
RECEIVER
VSX-LX51_HY.book 72 ページ ２００８年４月１６日 水曜日 午後４時３９分