Filter
Top Products
Listening to your system
05
28
En
• PhonesSurround – When listening through
headphones, you can still get the effect of overall
surround.
Tip
• When an Advanced Surround listening mode is
selected, the effect level can be adjusted using the
EFFECT parameter in Setting the AV options on
page 58.
Listening in stereo
When you select STEREO, you will hear the source
through just the front left and right speakers (and
possibly your subwoofer depending on your speaker
settings). Dolby Digital, DTS and WMA9 Pro
multichannel sources are downmixed to stereo.
• While listening to a source, press
STEREO/F.S.SURR
for stereo playback.
Press repeatedly to switch between:
• STEREO – The audio is heard with your surround
settings and you can still use the Midnight,
Loudness, and Tone functions.
• F.S.SURR FOCUS – See Using Front Stage Surround
Advance below for more on this.
• F.S.SURR WIDE – See Using Front Stage Surround
Advance below for more on this.
Using Front Stage Surround Advance
The Front Stage Surround Advance function allows you to
create natural surround sound effects using just the front
speakers and the subwoofer.
• While listening to a source, press
STEREO/F.S.SURR
to select Front Stage Surround Advance modes.
• STEREO – See Listening in stereo above for more on
this.
• F.S.SURR FOCUS – Use to provide a rich surround
sound effect directed to the center of where the front
left and right speakers sound projection area
converges.
• F.S.SURR WIDE – Use to provide a surround sound
effect to a wider area than FOCUS mode.
1
Using Stream Direct
Use the Stream Direct modes when you want to hear the
truest possible reproduction of a source. All unnecessary
signal processing is bypassed, and you’re left with the
pure analog or digital sound source (see Stream direct
with different input signal formats on page 80).
1 While listening to a source, press S.DIRECT
(
AUTO
SURR
/
STREAM DIRECT
)
to select the mode you want.
Check the digital format indicators in the front panel
display to see how the source is being processed.
• AUTO SURROUND – See Auto playback on page 26.
• DIRECT – Sources are heard according to the
settings made in the Surround Setup (speaker
setting, channel level, speaker distance, acoustic
calibration EQ, and X-curve), as well as with dual
mono, the input attenuator, and any sound delay and
hi-bit/hi-sampling settings. You will hear sources
according to the number of channels in the signal.
• PURE DIRECT – Analog sources are heard without
any digital processing. No sound is output from the
Second Zone in this mode.
SHIFT
STATUS
SIGNAL SEL
THX
ADV.SURR
SB ch
MULTI OPE
STANDARD
PHASE
S.DIRECT
MCACC
RECEIVER
STEREO/
F.S.SURR
PHOTO
SHIFT
STATUS
SIGNAL SEL
THX
ADV.SURR
SB ch
MULTI OPE
STANDARD
PHASE
S.DIRECT
MCACC
RECEIVER
STEREO/
F.S.SURR
PHOTO
Note
1 When using F.S.SURR WIDE, a better effect can be obtained if Auto MCACC Setup is performed. For more on this, refer to Automatically setting up for
surround sound (Auto MCACC) on page 8.
Front left
speaker
Front right
speaker
FOCUS position (Recommend)
Front left
speaker
Front right
speaker
WIDE position
SHIFT
STATUS
SIGNAL SEL
THX
ADV.SURR
SB ch
MULTI OPE
STANDARD
PHASE
S.DIRECT
MCACC
RECEIVER
STEREO/
F.S.SURR
PHOTO
VSX-LX50_HY.book Page 28 Thursday, March 8, 2007 1:18 PM