Filter
Top Products
PREPARATION
PREPARATION
31
En
Displays & Controls
(+/–) buttons (see page 52)
Use to adjust the TONE level, effect level and
channel level as well as make Dolby Pro Logic
II MUSIC parameter settings.
EFFECT/CH SEL. button
Switches between the diffeerent channels so
you can add volume individually to each
channel with the + and – buttons. Also selects
EFFECT mode of PIONEER original sound
modes and Dolby Pro Logic II MUSIC parame-
ter settings. You can then use the + and –
buttons to make these adjustments.
SIGNAL SELECT button (see page 45)
Press SIGNAL SELECT repeatedly to select one
of the following:
AUTO – If there are analog and digital signals
input, the receiver automatically selects the
digital signal.
DIGITAL – To select an optical or coaxial
digital signal.
ANALOG – To select an analog signal.
DIGITAL NR (DNR) button (see page 50)
Switches the DIGITAL NR on or off.
VIDEO SELECT button (see page 56)
Use to toggle between the different video input
possibilities.
HI-BIT button (see page 53)
Use this button to switch the HI-BIT
HI-SAMPLING on or off. Use to hear CD and
DVD, as well as other digital soundtracks at a
wider dynamic range, allowing for finer audio
reproduction.
5 SYSTEM SETUP button
Use for all system setups, including the
speaker and sound systems. For more informa-
tion see. “Setting up for Surround Sound“
starting on page 36. For a DVD player use this
button to bring up the DVD menu and for a
tuner use this button in the same way as the
TUNER EDIT button.
6 5˜∞˜2˜3˜ENTER buttons
These buttons can be used for a variety of
operations in the SYSTEM SETUP menu.
These buttons are used to control the menus
for other components when in those modes
(DVD, digital TV tuner, satellite tuner, cable
tuner, etc.). In TUNER mode, they can select a
station and/or a frequency.
7 AUDIO button
Use to switch the audio tracks of a DVD when
in DVD mode.
8 Command button for other components
(see pages 70-71)
Use these buttons to control other components
you selected with the MULTI CONTROL
buttons. You must input the preset code in
order use this function (see page 66-67).
9 TV CONTROL buttons
The following buttons are used to control the TV
only and can be used once they are preset to
control your TV.
TV INPUT: Press to select the input source for
the TV.
TV CH +/– : Use these buttons to change the
channel of the TV.
TV VOL +/– : Press to control the volume of
the TV.
0 Listening mode buttons (see page 46-
48)
SURROUND buttons (MOVIE, MUSIC,
||
||
|
\\
\\
\
& ENTER):
MOVIE: Press to put the receiver into MOVIE
listening mode (see page 47).
MUSIC: Press to put the receiver into MUSIC
listening mode (see page 48).
||
||
|
\\
\\
\: Use to select the MOVIE or MUSIC
listening mode.
ENTER: Use this button to enter information
concerning the listening modes.
STEREO/DIRECT: Switches the receiver into
STEREO mode if it was in a different sound
mode or toggles between DIRECT and
STEREO mode.
DIRECT playback bypasses the tone controls
and channel level for the most accurate
reproduction of a program source.
- SB CH MODE button (see pages 54)
Use this button to turn the surround back
channels ON/OFF/AUTO or switch the VIRTU-
AL SURROUND BACK mode between ON/
OFF/AUTO.
= SYSTEM OFF button (see pages 82-83)
This button turns off components in two ways.
First, when pressed it will turn off all PIONEER
components. Secondly, any component that
has programmed into the SYSTEM OFF
settings will be turned off.
For example: If you programmed power off in
the SYSTEM OFF settings for your TV and VCR,
pressing the SYSTEM OFF button will turn off
these components even if they are not
PIONEER products.
~ RECEIVER (STANDBY/ON) button
Press to turn power of the receiver on or to
standby (off).