Filter
Top Products
81
EXPERT
Fine Tuning Your System
FINE CHANNEL LEVEL
The following steps show you how to balance the sound output level of your speakers more finely than in the
NORMAL setup (see page 36). Proper speaker balance is essential for obtaining high quality surround sound and
the better the speaker balance the better surround sound you can get. Do this procedure if you want to try and
get even finer surround sound.
The main difference with this setup method and the CHANNEL LEVEL setup method in NORMAL setup is that
here the test tone alternates between the front left speaker (which is used as the reference channel) and the
target speaker (that is, the speaker whose level you want to adjust). Listen to the two tones and try to make
them the same volume.
Follow steps 1-5 on page 79, if necessary, to get
to the starting point mentioned here.
1
FINE CH LEVEL should be
selected, if it isn’t use the 5∞
buttons to select it. Press ENTER.
LOUDNESS MIDNIGHT TONEDNR ATT
STEREO
TUNED
RDS
Hi-BIT/
MULTI-ROOM
SAMPLING
EON
RF ATT
MONO
Neo :6
DIGITAL
DTS ES EX
MPEG AAC
STEREO
PRO LOGIC
DSP
L
C
R
LFE
AUTO
SB CH
ON MOVIE
MUSIC
OFF
L
S
S R
S
AUTO
RF
DIGITAL
dB
SIGNAL
SP A B
ANALOG
2
Use the 5∞ buttons to select the
channel you want to adjust.
Press ENTER.
LOUDNESS MIDNIGHT TONEDNR ATT
STEREO
TUNED
RDS
Hi-BIT/
MULTI-ROOM
SAMPLING
EON
RF ATT
MONO
Neo :6
DIGITAL
DTS ES EX
MPEG AAC
STEREO
PRO LOGIC
DSP
L
C
R
LFE
AUTO
SB CH
ON MOVIE
MUSIC
OFF
L
S
S R
S
AUTO
RF
DIGITAL
dB
SIGNAL
SP A B
ANALOG
Test tones will be output.
WARNING : Be prepared! The test tones are
output at a high volume level.
MASTER VOLUME rotates to the reference
position (0 dB) and the display on the receiver
flashes TEST TONE. After a few seconds the test
tone is output.
CHANNEL
−
CHANNEL
+
DTV ON/OFF BAND
D.ACCESS
MPX
CLASS
MENU TOP MENU
TUNER EDIT
GUIDE
SYSTEM
SETUP
AUDIO
RETURN
ST
TUNE
MASTER
VOLUME
ST
TUNE
ENTER
1-5
The adjustable channels are:
R (Front right), C (Center), LS (Surround left), RS
(Surround right), SBL (Surround back left), SBR
(Surround back right) and SW (Subwoofer).
3
Adjust the level of the channel
using the 5∞ buttons.
LOUDNESS MIDNIGHT TONEDNR ATT
STEREO
TUNED
RDS
Hi-BIT/
MULTI-ROOM
SAMPLING
EON
RF ATT
MONO
Neo :6
DIGITAL
DTS ES EX
MPEG AAC
STEREO
PRO LOGIC
DSP
L
C
R
LFE
AUTO
SB CH
ON MOVIE
MUSIC
OFF
L
S
S R
S
AUTO
RF
DIGITAL
dB
SIGNAL
SP A B
ANALOG
Try to get the volume level of the target speaker
to match that of the front left speaker, which is
the reference in this setup. The levels can be set
within a range of –10 dB to +10 dB in 0.5 dB
steps.
When you press ENTER you will automatically go
to the next channel.
4
Press ENTER to select a new
channel. Repeat step 3 for every
channel.
If you want to change a setting before
proceeding
Use the 5∞ buttons to go back to the channel
you want to adjust and press ENTER. Then
follow step 3.
5
When done select EXIT (if it's not
already selected) and press
ENTER.
LOUDNESS MIDNIGHT TONEDNR ATT
STEREO
TUNED
RDS
Hi-BIT/
MULTI-ROOM
SAMPLING
EON
RF ATT
MONO
Neo :6
DIGITAL
DTS ES EX
MPEG AAC
STEREO
PRO LOGIC
DSP
L
C
R
LFE
AUTO
SB CH
ON MOVIE
MUSIC
OFF
L
S
S R
S
AUTO
RF
DIGITAL
dB
SIGNAL
SP A B
ANALOG
Next, if you want, proceed to FINE CHANNEL
DELAY.
STANDBY/ON
MOVIE MUSIC
MULTI JOG
ENTER
STANDBY
PHONES
SPEAKERS
SIGNAL
SELECT
HI-BIT
HI-SAMPLING
SB CH
MODE
SET UP RETURN
TONE
TONE CONTROL
BASS/TREBLE
BANDMIDNIGHT LOUDNESS
MULTI JOG CONTROL
1-5