Filter
Top Products
Advanced Operations
En-84
■ HDMI Through
`Off
`BD/DVD, CBL/SAT, STB/DVR, GAME1, GAME2,
PC, AUX, TV/CD, PHONO:
Selects the input source for which the HDMI
Through function is enabled.
`Last:
The HDMI Through function is activated on the input
source selected at the time of setting the AV receiver
to standby mode.
When enabling the HDMI Through function, regardless of
whether the AV receiver is on or in standby, both audio
and video streams from an HDMI input will be output to
the TV or other components via HDMI connection. The
HDMI indicator will be dimly-lit in standby mode. Note
that the indicator may not light under certain conditions
(
➔ page 62).
This setting is fixed to “Auto” automatically when the
above “HDMI Control(RIHD)” setting is set to “On”,
resulting in automatic input source selection.
Note
• Only an input source assigned to an HDMI IN via “HDMI Input”
setting is enabled (➔ page 64).
• The power consumption in standby mode will increase during the
HDMI Through function; however in the following cases, the
power consumption can be saved:
– The TV is in standby mode.
– You are watching a TV program.
• Refer to the connected component’s instruction manual for
details.
• Depending on the connected component, the correct input source
may not be selected with the setting fixed to “Auto”.
• This setting is set to “Off” automatically when the “HDMI
Control(RIHD)” setting is set to “Off”.
■ Audio TV Out
`Off
`On
This preference determines whether the incoming audio
signal is output from the HDMI output. You may want to
turn this preference on if your TV is connected to the
HDMI output and you want to listen to the audio from a
connected component through your TV’s speakers.
Normally, this should be set to “Off”.
Note
• If “On” is selected and the audio can be output from the TV, the
AV receiver will output no sound through its speakers. In this
case, “TV Speaker” appears on the AV receiver’s display by
pressing DISPLAY.
• When “HDMI Control(RIHD)” is set to “On”, this setting is
fixed to “Auto”.
• When Digital Processing Crossover Network is being used, this
setting is not available.
• With some TVs and input signals, no sound may be output even
when this setting is set to “On”.
• When “Audio TV Out” or
“HDMI Control(RIHD)” is set to
“On” and you’re listening through your TV’s speakers
(➔ page 21), turning up the AV receiver’s volume control will
make the sound be output from the AV receiver’s front left and
right speakers. To stop the AV receiver’s speakers producing
sound, change the settings, change your TV’s settings, or turn
down the AV receiver’s volume.
• Listening mode cannot be changed when this setting is set to
“On” and the input source is not HDMI.
■ Audio Return Channel (ARC)
`Off
`Auto:
The audio signal from your TV tuner can be sent to
HDMI OUT MAIN of the AV receiver.
The audio return channel (ARC) function allows an ARC
capable TV to send the audio stream to HDMI OUT MAIN
of the AV receiver. To use this function, you must select
the TV/CD input selector and your TV must be ARC
capable. Default setting: “
----”
Note
• This setting is fixed to “----” when the “HDMI
Control(RIHD)” setting is set to “Off”.
• This setting is set to “Auto” automatically when the “HDMI
Control(RIHD)” setting is set to “On” for the first time.
• If you set “Audio Return Channel” to “Auto”, the “Audio
Selector” settings of the TV/CD input selector will be
automatically switched to “ARC” (➔ page 80).
■ Lip Sync
`Off
`On
This function allows the AV receiver to automatically
correct any delay between the video and the audio, based
on the data from the connected monitor.
Note
• This function works only if your HDMI-compatible TV supports
HDMI Lip Sync.
After changing the settings of the “HDMI
Control(RIHD)”, “HDMI Through” or “Audio
Return Channel”, turn off the power on all connected
pieces of equipment and then turn them on again. Refer
to the user’s manuals for all connected pieces of
equipment.