Filter
Top Products
Advanced Operations
En-75
LFE Level
■ Dolby Digital
*1
, DTS
*2
, Multich PCM, Dolby
TrueHD, DTS-HD Master Audio, DSD
*3
`– dB, –20dB, –10dB, or 0dB
With these settings, you can set the level of the LFE (Low
Frequency Effects) channel individually for each input
sources.
If you find that low-frequency effects are too loud when
using one of these sources, change the setting to –20 dB or
– dB.
*1
Dolby Digital and Dolby Digital Plus sources
*2
DTS and DTS-HD High Resolution sources
*3
DSD (Super Audio CD) sources
Direct
■ Analog
Subwoofer
`Off
`On:
Analog audio signals (bass signals) are output.
This setting determines whether or not analog audio signals
(bass signals) are output from front speakers when the Pure
Audio or Direct listening mode is selected.
Note
• If the “Subwoofer” setting is set to “No” (➔ page 67), this
setting cannot be selected.
• When Digital Processing Crossover Network is being used, this
setting is not available.
■ DSD
DAC Direct
`Off
`On:
DSD signals are not processed by the DSP.
This setting determines whether or not DSD (Super Audio
CD) audio signals are passed through the DSP for A/V
Sync, delay, etc., processing when the Pure Audio or
Direct listening mode is selected.
Note
• When Digital Processing Crossover Network is being used, this
setting is not available.
Sound Program Edit
■ Sound Program
`Stereo Source 1, Stereo Source 2, Stereo Source 3,
Multich Source 1, Multich Source 2, Multich
Source 3
When playing back different content types on the same
source, or when listening to a single content type on
different sources, you can pre-register the settings that best
suit each content in “Sound Program”. The registered
settings can then be called up and modified in one set. Use
“Sound Program Edit” to register and modify a
combination of settings.
Tip
• To select the registered settings, see “Sound Program”
(➔ page 58).
■ Listening Mode
You can assign a default listening mode that will be
selected automatically when you select the sound program.
The “Last Valid” option means that the listening mode
selected last will be used.
The “Straight Decode” option means that straight
decoding listening mode (Dolby Digital, DTS, etc.) is
selected.
■ Subwoofer
`No, Yes
You can choose whether or not to use the subwoofer with
the sound program.
■ Music Optimizer
*1
`Off, On
See “Music Optimizer” (➔ page 60).
■ Equalizer
*1
`Off
`Manual:
The manual setting in “Equalizer Settings”
(➔ page 70) is applied.
■ Audyssey
*1
`Off, Movie, Music
See “Audyssey” (➔ page 59).
■ Dynamic EQ
*1*2
`Off, On
See “Dynamic EQ” (➔ page 59).
■ Dynamic Volume
*1*2
`Off, Light, Medium, Heavy
See “Dynamic Volume” (➔ page 59).
■ Dolby Volume
*1
`Off, On
See “Dolby Volume” (➔ page 59).
Note
•“Listening Mode” is only available when the input signal
matches the setting of “Sound Program”.
• You cannot select the “Subwoofer” setting if you set it to “No”
in “Speaker Configuration”.
•“Music Optimizer” is only available when “Stereo Source 1”,
“Stereo Source 2” or “Stereo Source 3” is selected.
• When “Audyssey Quick Start” has been used for measurement,
the “Audyssey”setting cannot be selected.
*1
This setting cannot be used when the “Listening Mode”
setting is set to “Pure Audio” or “Direct”.
*2
To enable this setting, you must first perform the Room
Correction and Speaker Setup.