Onkyo HT-R980 Stereo Receiver User Manual


 
50
En
Audio Return Channel
`Off:
Select “Off” if you don’t want to use audio return
channel (ARC) function.
`Auto
:
The audio signal from your TV tuner can be sent to
the HDMI OUT of the AV receiver.
Audio return channel (ARC) function enables an HDMI
(Audio Return Channel) capable TV to send the audio
stream to the HDMI OUT of the AV receiver. To use this
function, you must select the TV/CD input selector and
your TV must support ARC function.
Note
•TheAudio Return Channel” setting can be set only when the
HDMI Control (RIHD)” setting is set to “On”.
This setting is set to “Auto” automatically when the “HDMI
Control (RIHD)” is set to “On” first time.
Power Control
`Off:
Power Control disabled.
`On
:
Power Control enabled.
To link the power functions of -compatible com-
ponents connected via HDMI, select “On”.
This setting is set to “On” automatically when the
HDMI Control (RIHD)” is set to “On” first time.
Note
•The
Power Control setting can be set only when the HDMI
Control (RIHD)
setting is set to “On”.
HDMI power control only works with -compatible
components that support it and may not work properly with
some components due to their settings or compatibility.
When set to “On”, power consumption will increase.
When set to “On”, regardless of whether the AV receiver is On
or in Standby, both audio and video stream from an HDMI input
will be output to the TV or other components via HDMI connec-
tion (HDMI pass through function). When the HDMI pass
through function activates in standby mode, HDMI THRU indi-
cator will light.
The power consumption during standby mode will increase dur-
ing the HDMI pass through function; however in the following
cases, the power consumption can be saved:
1. The TV is in standby mode.
2. You are watching a TV program.
Refer to the connected component’s instruction manual for
details.
TV Control
`Off:
TV Control disabled.
`On
:
TV Control enabled.
Set to “On” when you want to control the AV receiver
from an -compatible TV that is connected to
HDMI.
Note
Do not assign the component connected with the HDMI input to
the TV/CD selector when you set “TV Control” setting to “On”.
Otherwise, appropriate CEC (Consumer Electronics Control)
operation is not guaranteed.
•Set to
Off when the TV is not compatible or when it is unclear
whether the TV is compatible or not.
•The
TV Control setting can be set only when the HDMI
Control (RIHD)
(49) and Power Control settings are
both set to “On”.
Refer to the connected component’s instruction manual for
details.
With this preference, you can protect your settings by
locking the setup menus.
Main menu Lock Setup
Setup
`Locked:
Setup menus locked.
`Unlocked
:
Setup menus not locked.
When the setup menus are locked, you cannot change any
setting.
You can change various audio settings from the Audio
menu (22).
Note
These settings are disabled when:
a pair of headphones is connected, or
•theAudio TV Out” setting is set to “On” (49) and an input
selector other than HDMI is selected.
Tone Control Settings
You can adjust the bass and treble for the front speakers,
except when the Direct or THX listening mode is selected.
Bass
`–10dB to 0dB
to +10dB in 2 dB steps.
You can boost or cut low-frequency sounds output
by the front speakers.
Treble
`–10dB to 0dB
to +10dB in 2 dB steps.
You can boost or cut high-frequency sounds output
by the front speakers.
After changing the settings of the “HDMI Control
(RIHD)”, “Audio Return Channel”, “Power Con-
trol”, or “TV Control”, turn off the power to all con-
nected pieces of equipment and then turn them on again.
Refer to the user’s manuals for all connected pieces of
equipment.
Lock Setup
Using the Audio Settings
1
Press RECEIVER followed by AUDIO.
2
Use // / to make the desired selection.