Filter
Top Products
4
■ 2 × 20 watts min RMS at 4 ohms, 1 kHz no more than
1.0 % THD (FTC rating)
■ 2 × 20 watts at 4 ohms, 1 kHz, DIN
■ 2 × 25 watts at 4 ohms, EIAJ
■ 4-Ohm Drive capability
■ High-Grade Discrete Outputs Stage Circuits
■ Brushed Aluminium Front Panel
■ 4-step Acoustic Presence control
■ Illuminated Volume knob
■ Optical Digital Output
■ Full-Function Remote Control
U.S. & Canadian models
■ Subwoofer Preout
■ CDR and Tape Inputs/Outputs
European and Asian models
■ Auto Digital Level Adjustment for Synchro-Recording
(When connected to MD-105X/TX or CDR-205X/TX)
■ MD, CDR, and Tape Inputs/Outputs
■ RDS (PS) (European models)
Features
For U.S. model
The laser is covered by a housing which prevents exposure during
operation or maintenance. However, this product is classified as a
Laser Product by CDRH (Center for Devices and Radiological Health)
which is a department of the Food and Drug Administration. Accord-
ing to their regulations 21 CFR section 1002.30, all manufactures
who sell Laser Products must maintain records of written communi-
cations between the manufacturer, dealers and customers concerning
radiation safety. If you have any complaints about instructions or
explanations affecting the use of this product, please feel free to write
to the address on the back page of this manual. When you write us,
please include the model number and serial number of your unit.
In compliance with Federal Regulations, the certification, identifi-
cation and the period of manufacture are indicated on the rear panel.
FCC Information for User
CAUTION:
The user changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment gen-
erates, uses and can radiate radio frequency energy and, if not in-
stalled and used in accordance with the instructions, may cause harm-
ful interference to radio communications. However, there is no guar-
antee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s atten-
tion to Section 820-40 of the NEC which provides guidelines for
proper grounding and, in particular, specifies that the cable ground
shall be connected to the grounding system of the building, as close
to the point of cable entry as practical.
For Canadian model
NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES
WITH CANADIAN ICES-003.
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
Modèle pour les Canadien
REMARQUE: CET APPAREIL NUMÉRIQUE DE LA CLASSE
B EST CON-FORME À LA NORME NMB-003 DU CANADA.
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS
LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
For British model
Replacement and mounting of an AC plug on the power supply cord
of this unit should be performed only by qualified service personnel.
IMPORTANT
The wires in the mains lead are coloured in accordance with the
following code:
Blue : Neutral
Brown : Live
As the colours of the wires in the mains lead of this apparatus may
not correspond with the coloured markings identifying the terminals
in your plug, proceed as follows:
The wire which is coloured blue must be connected to the terminal
which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the termi-
nal which is marked with the letter L or coloured red.
Memory Preservation
This unit does not require memory preservation batteries. A built-
in memory power back-up system preserves the contents of the
memory during power failures and even when the unit is un-
plugged. The unit must be plugged in order to charge the back-up
system.
The memory preservation period after the unit has been unplugged
varies depending on climate and placement of the unit. On the
average, memory contents are protected over a period of a few
weeks after the last time the unit has been unplugged. This pe-
riod is shorter when the unit is exposed to a highly humid cli-
mate.
IMPORTANT
A 5 ampere fuse is fitted in this plug. Should the fuse need to be
replaced, please ensure that the replacement fuse has a rating of 5
amps and that it is approved by ASTA or BSI to BS1362. Check for
the ASTA mark or the BSI mark on the body of the fuse.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE
SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD
BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF
SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL
SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13
AMPERE SOCKET.
If in any doubt, please consult a qualified electrician.