Filter
Top Products
44
To change the transmittable signals for
operating a CATV converter or DBS tuner
1. Set the remote control mode to “CATV/DBS.”
2. Press and hold TV/CATV/DBS POWER.
3. Press TV/DBS.
4. Enter manufacturer’s code (three digits) using
buttons 1–9, and 0.
See the list below.
Examples: For a Pioneer product, press 1, then 3.
For a Sony product, press 2, then 0.
5. Release TV/CATV/DBS POWER.
After setting the remote control mode selector to “CATV/DBS,”
you can perform the following operations on the CATV
convertor or on the DBS tuner:
TV/CATV/DBS POWER Turns on and off the CATV converter
or DBS tuner.
CHANNEL +/– Changes the channels.
1 – 10, 0, 100+ (+10) Selects the channel.
100+ (+10) button will function as
the ENTER button if your equipment
requires pressing ENTER after
selecting a channel number.
Note:
Refer to the manual supplied with your CATV converter or DBS
tuner.
6. Try to operate your CATV converter or DBS
tuner by pressing TV/CATV/DBS POWER.
When your CATV converter or DBS tuner turns on or off, you
have entered the correct code.
If there are more than one code listed for your brand of
CATV converter or DBS tuner, try each one until the correct
one is entered.
Manufacturer Codes
GI/JERROLD 01, 02, 03, 04, 05,
06, 07, 08
HAMLIN/REGAL 15, 16, 17, 18
PIONEER 13, 14
RCA 19
SCIENTIFIC ATLANTA 09, 10
SONY 20
ZENITH 11, 12
Manufacturers’ codes are subject to change without
notice. If they are changed, this remote control cannot
operate the equipment.
To change the transmittable signals for
operating another manufacturer’s VCR
1. Set the remote control mode to “AUDIO/TV/
VCR.”
2. Press and hold VCR POWER.
3. Press VCR.
4. Enter manufacturer’s code (two digits) using
buttons 1–9, and 0.
See the list below.
Examples: For a JVC product, press 0, then 1.
For a Funai product, press 1, then 0.
5. Release VCR POWER.
Following button can be used for operating the VCR (with the
remote control mode selector set to “AUDIO/TV/VCR”):
VCR POWER Turns on and off the VCR.
After pressing VCR or VCR CONTROL (with the remote
control mode selector set to “AUDIO/TV/VCR”), you can
perform the following operations on the VCR:
CHANNEL +/– Changes the TV channels on the VCR.
1 – 10, 0, 100+ (+10) Selects the TV channels.
100+ (+10) button will function as
the ENTER button if your VCR
requires pressing ENTER after
selecting a channel number.
PLAY Starts playback.
1 Rewinds a video tape.
¡ Fast winds a video tape.
STOP Stops operation.
PAUSE Pauses.
¶ REC: Starts recording or enters recording pause.
Notes:
• Refer to the manual supplied with your VCR.
• You can use either VCR button or the VCR CONTROL button to
activate the buttons listed above. If you press VCR, the playing
source also changes. On the other hand, if you press VCR
CONTROL, the playing source does not change.
6. Try to operate your VCR by pressing VCR
POWER.
When your VCR turns on or off, you have entered the correct
code.
If there are more than one code listed for your brand of
VCR, try each one until the correct one is entered.
Manufacturer Codes Manufacturer Codes
JVC 01, 02, 03 PHILIPS 09
EMERSON 11, 26 RCA 05, 06
FISHER 29 SAMSUNG 24
FUNAI 10, 14, 15, 16 SANYO 21, 22, 23
GOLD STAR 12 SHARP 27, 28
HITACHI 04 SHINTOM 30
MITSUBISHI 13 SONY 18, 19, 20
NEC 25 TOSHIBA 26
PANASONIC 07, 17 ZENITH 08
Manufacturers’ codes are subject to change without notice. If they
are changed, this remote control cannot operate the equipment.
EN39Å[47.RX-778V[J]/1 99.3.8, 11:42 AM44