Filter
Top Products
23
DSP MODE
IMPORTANT:
When using the remote control, check to see if its
remote control mode selector is set to the correct
position:
To operate this receiver, set it to “AUDIO/TV/
VCR” (except when selecting the DBS tuner as
the source).
Adjusting the 3D-PHONIC Modes
Once you have adjusted the 3D-PHONIC modes, the adjustment is
memorized for each 3D-PHONIC mode.
Before you start, remember...
• Make sure that you have set the speaker information correctly
(see page 14).
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
On the front panel:
1. Press DSP MODE repeatedly until
“3D ACTION (or 3D DIGITAL)”
or “3D THEATER” appears on
the display.
The 3D-PHONIC, DSP, PRO LOGIC and selected 3D-PHONIC
mode indicators also light up on the display.
2. Adjust the effect level.
1) Press BALANCE/SURROUND
ADJUST repeatedly until “DSP
EFFECT” appears on the display.
The display changes to show the current
setting.
2) Turn MULTI JOG to select the effect
level.
• As you turn it, the effect level changes
as follows:
As the number increases, the selected 3D-PHONIC mode
becomes stronger.
From the remote control:
1. Press SURROUND MODE
repeatedly until “3D ACTION (or
3D DIGITAL)” or “3D
THEATER” appears on the
display.
The 3D-PHONIC, DSP, PRO LOGIC and selected 3D-PHONIC
mode indicators also light up on the display.
2. Press SOUND.
The 10 keys are activated for sound adjustments.
AUDIO/
TV/VCR
CATV/DBS
BALANCE/SURROUND
ADJUST
MULTI JOG
3. Press EFFECT to select an effect
level you want.
• Each time you press the button, the effect
level changes as follows:
As the number increases, the selected 3D-PHONIC mode
becomes stronger.
Adjusting the DAP Modes
Once you have adjusted the DAP modes, the adjustment is
memorized for each DAP mode.
Before you start, remember...
• Make sure that you have set the speaker information correctly
(see page 14).
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
• You cannot adjust the rear speaker output level when you have set
“REAR SPK” to “NONE.” See page 14.
• When the DAP mode is used with the SEA mode (see page 19),
sounds may be distorted. If this happens, turn off the SEA mode.
On the front panel:
1. Press DSP MODE repeatedly until
the DAP mode — LIVE CLUB,
DANCE CLUB, HALL, or
PAVILION — appears on the
display.
The DSP and selected DAP mode indicators also light up on the
display.
• When you have set “REAR SPK” to “NONE,” the 3D-
PHONIC indicator also lights up.
2. Adjust the speaker output levels.
1) Press BALANCE/SURROUND
ADJUST repeatedly until one of the
indications appears on the display.
“REAR L LEVEL”:
To adjust the left rear speaker level.
“REAR R LEVEL”:
To adjust the right rear speaker level.
2) Turn MULTI JOG to adjust the
selected speaker output level (from –10
dB to +10 dB).
3) Repeat 1) and 2) to adjust the other
speaker output level.
DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3
DSP EFFECT 4DSP EFFECT 5
EFFECT
7/P
DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3
DSP EFFECT 4DSP EFFECT 5
SOUND
SURROUND
MODE
MULTI JOG
BALANCE/SURROUND
ADJUST
DSP MODE
EN19Å[27.RX-778V[J]/1 99.3.2, 3:14 PM23