Filter
Top Products
42
Turntable
After pressing PHONO (with the remote control mode selector set to
“AUDIO/TV/VCR”), you can perform the following operations on a
turntable:
PLAY: Starts playing.
STOP: Stops operations.
Cassette deck
After pressing TAPE/MD or TAPE CONTROL (with the remote
control mode selector set to “AUDIO/TV/VCR”), you can perform
the following operations on a cassette deck:
PLAY: Starts playing.
11
11
1: Fast winds the tape from right to left.
¡¡
¡¡
¡: Fast winds the tape from left to right.
STOP: Stops operations.
PAUSE: Pauses playing. To release it, press PLAY.
¶ REC: Press this button with the PLAY button to start
recording.
Press this button with the PAUSE button to enter
recording pause.
MD recorder
After pressing TAPE/MD or TAPE CONTROL (with the remote
control mode selector set to “AUDIO/TV/VCR”), you can perform
the following operations on the MD recorder:
PLAY: Starts playing.
4: Returns to the beginning of the current (or previous)
track.
¢: Skips to the beginning of the next track.
STOP: Stops playing.
PAUSE: Pauses playing. To release it, press PLAY.
¶ REC: Press this button with the PLAY button to start
recording.
Press this button with the PAUSE button to enter
recording pause.
Note:
You can use either TAPE/MD button or the TAPE CONTROL button to
activate the buttons listed above. If you press TAPE/MD, the playing
source also changes. On the other hand, if you press TAPE
CONTROL, the playing source does not change.
IMPORTANT:
To operate JVC’s video components using this remote control:
• You need to connect JVC video components through the AV
COMPU LINK terminals (see page 39) in addition to the
connections using cables with RCA pin plugs (see page 7).
• Some JVC VCRs can accept two types of the control signals —
remote code “A” and “B.” Before using this remote control, make
sure that the remote control code of the VCR connected to the
VCR jacks is set to code “A.”
• When using the remote control:
– For the DVD player and VCR operations, aim the remote control
directly at the remote sensor on each component, not on the
receiver.
– For the TV operations:
7 If the TV having the AV COMPU LINK terminal
“RECEIVER/AMP,” aim the remote control directly at the
remote sensor on the receiver.
7 If the TV having the AV COMPU LINK terminal “AV
COMPU LINK EX,” aim the remote control directly at the
remote sensor on the TV.
VCR
You can always perform the following operations (with the remote
control mode selector set to “AUDIO/TV/VCR”):
VCR POWER: Turns on or off the VCR.
After pressing VCR or VCR CONTROL (with the remote control
mode selector set to “AUDIO/TV/VCR”), you can perform the
following operations on the VCR:
1 – 9, 0: Selects the TV channels on VCR.
PLAY: Starts playing.
1: Rewinds a tape.
¡: Fast winds a tape.
STOP: Stops operations.
PAUSE: Pauses playing. To release it, press PLAY.
¶ REC: Press this button with the PLAY button to start
recording.
Press this button with the PAUSE button to enter
recording pause.
CHANNEL +/–: Changes the TV channels on the VCR.
Note:
You can use either VCR button or the VCR CONTROL button to
activate the buttons listed above. If you press VCR, the playing source
also changes. On the other hand, if you press VCR CONTROL, the
playing source does not change.
DVD player
After pressing DVD (with the remote control mode selector set to
“AUDIO/TV/VCR”), you can perform the following operations on a
DVD player:
PLAY: Starts playing.
4: Returns to the beginning of the current (or previous) track.
¢: Skips to the beginning of the next track.
STOP: Stops playing.
PAUSE: Stops playing temporarily. To release it, press PLAY.
After pressing DVD, these buttons
can be used for the DVD menu
operations.
Note:
For detailed menu operations, refer to the
instructions supplied with the discs or the
DVD player.
TV
You can always perform the following operations (with the remote
control mode selector set to “AUDIO/TV/VCR”):
TV/CATV/DBS POWER: Turns on or off the TV.
TV VOL +/–: Adjusts the volume.
TV/VIDEO: Sets the input mode (either TV or VIDEO).
After pressing TV/DBS (with the remote control mode selector set
to “AUDIO/TV/VCR”), you can perform the following operations
on a TV:
CHANNEL +/–: Changes the channels.
1 – 9, 0, 100+: Selects the channels.
RETURN: Alternates between the previously selected channel
and the current channel.
CNTR
TEST REAR•L
REAR•R
23
456
8
MENU
ENTER
EN39Å[47.RX-778V[J]/1 99.3.8, 11:42 AM42