Filter
Top Products
40 PROGRAMMING THE REMOTE
Programming the Remote
Code Readout
When the code has been entered using the Auto
Search method, it is always a good idea to find
out the exact code so that it may be easily
reentered if necessary. You may also read the
codes to verify which device has been
programmed to a specific Control Selector
button.
1. Press and hold both the Input Selector
4
for the device you wish to find the code for and
the Mute button
b
at the same time. Note
that the Program/SPL Indicator
2
will ini-
tally turn amber and begin flashing. Release the
buttons and begin the next step within 20 sec-
onds.
2. Press the Set button
F
.The Program/SPL
Indicator
2
will then blink green in a sequence
that corresponds to the three-digit code, with a
one-second pause between each digit. Count the
number of blinks between each pause to deter-
mine the digit of the code. One blink is the number
1, two blinks is the number 2, and so forth. Note
that a rapid sequence of three blinks is used to
indicate a “0.”
Example: One blink, followed by a one-second
pause, followed by six blinks, followed by a one-
second pause, followed by four blinks indicates
that the code has been set to 164.
For future reference enter the Setup Codes for the
equipment in your system here:
DVD ____________ CD ________________
VID1/VCR ________ VID2/TV __________
VID3/CBL/SAT ______________________
TAPE ______________________________
Learning Codes from a Remote
In addition to using codes from the remote’s
internal code library, the AVR5000’s remote is
able to “learn” codes from remotes that may not
be in the code library. In addition, you may use
this function to “learn over” the codes from a
preprogrammed device to add functions not
included in the preprogrammed codes. To learn
or transfer codes from an IR remote to the
AVR5000’s remote, follow these steps:
1. Place the front of the original remote with the
code being sent so that it is facing the IR
Transmitter Window
1
on the AVR5000
remote “head-to-head.” The remotes should be
between 2 and 4cm apart.
2. Select the button on the remote that you wish
to use as the device selector for the codes about
to be entered.This must be any of the Input
Selectors
4
(except for VID4).
3. Press the Input Selector
4
button chosen
and the Learn Button
7
at the same time.
Hold these buttons until the Program/SPL
Indicat
2
flashes amber and the light under
the device selector button turns red. Release the
buttons. It is important that you begin the next
step within 20 seconds.
4. Press the button on the AVR5000 remote that
you wish to program. Note that the Program/
SPL Indicat
2
will stop flashing.
Important Note: Codes cannot be taught to all
buttons on the remote. The buttons with the
following numbers are not learnable (for
numbers, see drawing on page 11): 6, 7, 8, 36,
37, 9, 12, 33, 19, 29, 20, 21, 22, 23, 26, 27, 28.
5.As long as the Program/SPL Indicator
2
is on, press and hold the button on the original
remote that you wish to “teach” into the
AVR5000 remote.When the Program/SPL
Indicator
2
turns green, release the button.
Note that the Program Indicator will then begin
to flash amber again.
NOTE: If the Program/SPL Indicator
2
turns
red during Step 5, the programming was not suc-
cessful. Repeat the steps to see if the code will
“take.” If the indicator keeps flashing red in
step 5, this code cannot be taught.
6. Repeat steps 4 though 5 for each button on
the source remote that you wish to transfer to
the AVR5000 remote.
7. Once all codes have been transferred from the
original source remote to the AVR5000 remote,
press the Learn button
7
.This will turn off all
LEDs and turn off the learning mode.
8. Repeat Steps 1 through 7 for any additional
remotes you wish to “teach” into the AVR5000
Remote.
Erasing Learned Codes
The AVR5000’s remote allows you to remove or
erase the code learned into a single button for a
single device, to remove or erase all the codes that
have been learned for a single device, or to erase
all commands that have been learned for all
devices.
To erase a single learned code from within a single
device’s settings, follow these steps:
1. Press and hold both the Input Selector
456
within which the individual button to
be erased has been programmed and the Learn
button
7
.
2.When the red LED under the Input Selector
turns red and the Program/SPL Indicator
2
flashes amber, release the buttons.
3. Press and release the Input Selector
456
again for the device within which the
individual button to be erased has been pro-
grammed.
4. Press the 7 button
H
three times.
5. Press and release the individual button for
which the code is to be erased.The Program/SPL
Indicator
2
will blink green two times and
then return to amber.
6.To erase other buttons within the same device,
press them as noted in Step 5.
7.When all buttons to be erased have been
pressed, press the Learn button
7
to complete
the process.
To erase all codes within a single device, follow
these steps:
1. Press and hold both the Input Selector
456
for which you wish to erase the
codes and the Learn button
7
.
2.When the red LED under the Input Selector
turns red and the Program/SPL Indicator
2
flashes amber, release the buttons.
3. Press and release the same Input Selector
456
again for the device whose codes
you wish to erase.
4. Press the 8 button
H
three times.
5.The Program/SPL Indicator
2
will turn off
and the red light under the Input Selector will
flash on and off once to indicate that the codes
have been erased.