Filter
Top Products
26 SYSTEM CONFIGURATION
Delay Settings
Due the different distances between the listening
position for the front channel speakers and the
surround speakers, the amount of time it takes
for sound to reach your ears from the front or
surround speakers is different. You may compen-
sate for this difference through the use of the
delay settings to adjust the timing for the specif-
ic speaker placement and acoustic conditions in
your listening room or home theater.
If you have already calibrated your system using
EzSet+ the delay settings shown will reflect the
results of the measurements made by EzSet+.
No further changes are needed unless you wish
to change an item to reflect your taste or a non-
standard system configuration.To change the
settings, follow the instructions below to enter
the distance between the speaker’s location and
your main listening position.The measurements
need not be accurate to the inch, as the system
is designed to accommodate typical listening
rather than a specific “sweet spot” position.
In addition to adjusting the delay time for each
individual speaker position, the AVR is among
the few A/V receivers that allows you to adjust
the delay for the combined output of all speakers
as a group. This feature is called A/V Sync Delay;
it allows you to compensate for delays to the
video image that may be caused by the process-
ing in products such as digital video displays,
video scalers, digital cable or satellite systems, or
personal video recorders. With proper adjustment
of the setting for A/V Sync Delay, you can elimi-
nate the loss of lip sync that may be caused by
digital video applications.
Although EzSet+ calculates the delay settings for
the individual speaker positions with very accu-
rate results, the setting for A/V Sync Delay may
only be done manually, since it requires that you
observe the program material on your video dis-
play while adjusting the delay, if any, required for
the specific source. Thus, even though you may
have used EzSet+ for other delay settings, the
A/V Sync Delay should still be configured as out-
lined below.
To re-synchronize the front, center and surround
channels at first measure and note the distance
from the listening/viewing position to the front,
center, surround and surround back (if any)
speakers in meters.
Due to the differences in the way each surround
mode operates, the delay settings must be estab-
lished individually for each surround mode.
However, once the delay settings are configured
for the version of the surround mode with the
most channels, they need not be entered again
for a version of that mode with fewer channels.
For example, once the delay settings are estab-
lished for Dolby Pro Logic IIx – Movie, they will
be carried over to Dolby Pro Logic II – Movie
mode. However, you will need to enter the delay
settings separately for each variant mode, such
as Dolby Pro Logic IIx – Music, Dolby Pro Logic
IIx – Game, Dolby Pro Logic, Dolby 3 Stereo and
Dolby Digital EX.
Delay times are adjustable for all surround
modes. Although all channels will appear on
screen with the default or previously entered dis-
tances, the menu system will only allow you to
adjust the settings for those channels which are
actually used by the current sur-round mode. For
example, when you are listening to music CDs
using the CD input in DSP Surround Off mode,
you may adjust the delay settings for the front
left, front right and subwoofer channels only. The
cursor will simply skip the other channels as you
navigate through the menu.Therefore, the first
time you adjust the delay settings, it is recom-
mended that you select a 5.1-, 6.1- or 7.1-chan-
nel surround mode, depending on the number of
speakers in your system. For the purposes of set-
ting the delay distances, the Logic 7 modes allow
access to the settings for all channels without
requiring that you play a source.
To start with the delay settings at first select the
DELAYADJUST MENU(Figure 13). If the
system is not already at that point, press the
OSD button
L
to bring up the master menu.
Press the
¤
Button
D
three times or until the
on-screen
➞ cursor is pointing at the MANUAL
SETUP
line. Press the Set Button
F
and
call up the
DELAYADJUST submenu.
Figure 13
Next move the ➞ cursor to the UNITline and
select the unit for distances you prefer to enter,
feet or meter.Then move the
➞ cursor to the
FLline where the first adjustment is made.
Now press the
‹
/
›
Buttons
Ea
until the
distance from the front left speaker to the pre-
ferred listening position is entered. Next press
the
¤
Button
D
once to move to the next
line.
Now the
➞ cursor will be at the CENline so
that the delay for the center speaker may be set.
Press the
‹
/
›
Buttons
Ea
until the dis-
tance from the main listening position to the
center speaker is entered. Repeat the procedure
for all active speaker positions by pressing the
¤
Button
D
again and use the
‹
/
›
Buttons
Ea
to change the setting. Remember that
this last adjustment will only be needed when
you have surround back speakers installed and
Dolby Digital chosen as the surround mode.
When the delay time for all speaker positions has
been set you may return to the master menu by
pressing the
⁄
/
¤
Navigation Button
D
until the ➞ cursor is pointing to BACKTO
MASTERMENU
and then pressing the Set
Button
F
.
However, if you have a digital video source or a
digital video display that causes lack of lip sync
you may use the A/V Sync adjust feature to delay
the audio signal as it is sent to all channels (as
opposed to the individual settings) so that the
picture and sound are brought back together.We
recommend that this adjustment be made using
the direct access controls on the remote, as
shown below. That enables you to see the image
while making the adjustment; however, you may
also adjust it here using the menu system.
To adjust the A/V Sync delay, press the
⁄
/
¤
Navigation Button
D
so that the ➞ cursor
is pointing to the A/V Sync Delay line on the
menu and then press the
‹
/
›
Navigation
Button
Ea
to delay the sound sufficiently
so that it matches the on-screen video.
The delay settings may be adjusted at any time
using the remote control and while viewing an
on-screen image by pressing the Delay Select
Button
Z
.The A/V Sync Delay setting is first,
and it may be adjusted by pressing the Set
Button
F
within five seconds of when the
A/V SYNC DELAY message appears in
the on-screen display and the Lower Display
Line
Ò
.Then, press the
‹
/
›
Navigation
Button
Ea
to enter the desired delay set-
ting that brings the video and sound back in
sync. Press the Set Button
F
again to enter
the setting.
Note that the A/V Sync delay setting is unique to
each video input source, so you may enter a dif-
ferent setting to compensate for the differences
between any product attached to the Video 1, 2,
3 or 4 inputs.
To change one of the individual speaker posi-
tions directly, press the Delay Select Button
Z
, followed by the
⁄
/
¤
Navigation
Button
D
to select the desired position as
that name appears in the on-screen display and
the Lower Display Line
Ò
.When the name of
the speaker position to be adjusted appears
press the Set Button
F
within five seconds.
Press the
‹
/
›
Navigation Button
Ea
to
enter the desired delay setting for that speaker
and then press the Set Button
F
to enter the
* DELAY ADJUST *
FL :10 FT SBR:10 FT
CEN:10 FT SBL:10 FT
FR :10 FT SL :10 FT
SR :10 FT SUB:10 FT
DELAY RESET: OFF
UNIT: FEET
A/V SYNC DELAY : 0mS
BACK TO MASTER MENU
›
System Configuration