Filter
Top Products
4
ENGLISH
!8 CLEAR button
Press this button to cancel the station-memory
setting mode or preset scan tuning. (See page 33)
!9 HT-EQ button
Used to turn on or off HT(Home Theater)-EQ mode.
This mode compensates for the audio portion of
a movie sounding “bright”. When this button is
pressed, “EQ” indicator lights up.
@0 MEMORY button
Press this button to enter the tuner preset memory
numbers or station names. (See page 33)
@1 PURE DIRECT button
When this button is pressed once, “SOURCE DIRECT”
appears on the FL display. If pressed again, “PURE
DIRECT” appears. After 2 seconds, the FL display
indication goes out.
In the source/pure direct mode, the tone control
circuitry and bass management are bypassed.
Notes:
• The surround mode is automatically switched to
AUTO when the pure direct/source direct function
is turned on.
• Additionally, speaker configurations are fixed
automatically as follows.
Front SPKR = LARGE
Center SPKR = LARGE
Surround SPKR = LARGE
Surround Back SPKR = LARGE
Sub woofer = YES
@2 AUTO (Auto surround) button
Press this button to select the AUTO mode from the
surround modes. When this mode is selected, the
receiver determines the surround mode corresponding
to a digital input signal automatically.
@3
HEADPHONE jack for stereo
headphones
This jack may be used to listen to the DN-A7100’s
output through a pair of headphones. Be certain
that the headphones have a standard 1 / 4” stereo
phono plug.
!0 MUTE button
Press this button to mute the PreAMP output. Press it
again to return to the previous volume level.
!1 VOLUME control knob
Adjusts the overall sound level. Turning the control
clockwise increases the sound level.
!2 ATT (Attenuate) button
If the selected analog audio input signal is greater
than the capable level of internal processing, the
PEAK indicator will illuminate. If this happens, you
should press the ATT button. “ATT” is displayed
when this function is activated.
The signal-input level is reduced by about half.
Attenuation will not work with the output signal of
“REC OUT” (TAPE, CD-R/MD and VCR output). This
function is memorized for each input function.
!3 INPUT SELECTOR knob
(AUDIO/ VIDEO)
This knob is used to select the input sources.
The video SOURCE, such as TV, DVD, VCR1 and
DSS, selects video and audio simultaneously.
Audio function sources such as CD, TAPE, CDR/MD,
and TUNER may be selected in conjunction with a
Video source.
This feature (Sound Injection) combines a sound
from one source with a picture from another.
Choose the video source fi rst, and then choose a
different audio source to activate this function.
!4 Cursor (1, 2, 3, 4) / ENTER button
Use these buttons when operating the SETUP MAIN
MENU and TUNER function.
!5 EXIT button
This button is used to exit from the SETUP MAIN
MENU.
!6 SIMPLE SETUP button
Press this button to enter the simple setup mode.
You can setup the speaker conditions (speaker sizes,
number of speakers, speaker delay times) quickly by
pressing the cursor buttons.
!7 DISPLAY button
When this button is pressed, the FL display mode
is changed as Surround Mode → Auto-display Off
→ Display Off → Input Function and the display off
indicator(DISP) lights up in condition of DISPLAY
OFF.
FRONT PANEL
o !0 !1
r
iu
y
w e t
@2 !8@0 !6
@1 !9 !7 !5@3 !2!3!4
q
q POWER switch and STANDBY
indicator
Press the button to turn the power ON, and press
again to turn it OFF. If the POWER switch is in the
ON position, the power of this unit can be turned ON/
OFF by pressing the POWER button on the remote
control unit.
When this unit is in the standby mode with the
POWER switch set to the ON position, pressing the
ENTER button also allows to turn the power on.
The STANDBY indicator lights up when this unit
is the standby mode (power OFF) by the remote
control unit.
w KEY LOCK button
Press and hold this button for 3 seconds to set
KEY LOCK mode. When the KEY LOCK mode is
on, the unit can only be operated from the RS232C
or remote control, and operation by the main unit
keys is prohibited. Press and hold this button for 3
seconds to release the KEY LOCK mode.
e KEY LOCK indicator
The indicator is illuminated when in KEY LOCK
mode.
r SURROUND MODE button
You can select the surround mode by pressing this
button.
t HDMI indicator
This indicator is illuminated when HDMI device is
connected to the DN-A7100.
y INFRARED receiving sensor
window
This window receives infrared signals for the remote
control.
u BAND button
Press this button to switch between FM and AM in
the TUNER mode.
i T-MODE button
Press this button to select the auto stereo mode or
mono mode when the FM band is selected.
The “AUTO” indicator lights in the auto stereo mode.
(See page 33)
o MENU button
This button is used to enter the SETUP MAIN
MANU.