Denon DN-A7100 Stereo Amplifier User Manual


 
6
ENGLISH
REAR PANEL
o!1!6!7 !2
q ewr ytiu
!0
!3!4!5
i HDMI INPUT/OUTPUT
This unit has 2 HDMI inputs and 1 HDMI output. The
input function can be selected from the OSD menu
system. (See page 20)
o AC INLET
Plug the supplied power cord into this AC INLET and
then into the power outlet on the wall.
DN-A7100 can be powered by 230V AC only.
!0 DC TRIGGER output terminal
Connect a device that needs to be triggered by DC
under certain conditions (screen, power strip, etc…)
Use the system OSD setup menu to determine the
conditions by which these jack will be active.
Note:
This output voltage is for (status) control only, It is not
suffi cient for drive capability.
!1 Analog audio output level switch
(-10dBV/+4dBu)
This switch changes the standard output level of the
Balanced Analog audio signal.
!2 Balanced Analog audio output
(L, R, SL, SR, SBL, SBR, C, SW)
Balanced Analog audio output (XLR) for L (front
left), R (front right), C (Center), SL (surround left),
SR (surround right), SBL (surround back left), SBR
(surround back right) and SW (subwoofer).
Use these jacks for connection to external power
amplifi ers.
!3 Subwoofer Output
Connect this jack to the line level input of a powered
subwoofer. If an external subwoofer amplifi er is used,
connect this jack to the subwoofer amplifi er input. If
you are using two subwoofers, either powered or
with a 2 channel subwoofer amplifi er, connect a “Y”
connector to the subwoofer output jack and run one
cable from it to each subwoofer amplifi er.
t MONITOR OUT
This is a monitor output and each one includes both
composite video and S-video confi gurations. When
connecting two video monitors or televisions, be
aware that the OSD interface can be used with both
MONITOR OUT connections.
y COMPONENT VIDEO INPUT/
OUTPUT
If your DVD player or other device has component
video connectors, be sure to connect them to these
component video connectors on the DN-A7100.
The DN-A7100 has two component video input
connectors to obtain the color information (Y, C
B
,
C
R
) directly from the recorded DVD signal or other
video component and one component video output
connector to output it directly into the matrix decoder
of the display device.
By sending the pure DVD component video signal
directly, the DVD signal forgoes the extra processing
that normally would degrade the image. The result is
vastly increased image quality, with incredibly life like
colors and crisp detail.
When the video convert function is enabled, video and
S-video images can be output to the COMPONENT
MOINTOR OUT jack.
u DIGITAL INPUT (Dig.1-5) /
OUTPUT (coaxial, optical)
These are the digital audio inputs and outputs. There
are 2 digital inputs with coaxial jacks, 3 with optical
jacks.
The inputs accept digital audio signals from a CD,
DVD, or other digital source component.
For digital output, there is 1 coaxial output and 1
optical output.
The digital outputs can be connected to MD recorders,
CD recorders, or other similar components.
q 7.1 CHANNEL or AUX2 INPUT
By connecting a DVD Audio player, SACD
multichannel player, or other components that has
a multichannel port, you can playback the audio with
5.1 channel or 7.1 channel outputs.
w FM antenna terminal (75 ohms)
Connect an external FM antenna with a coaxial
cable, or a cable network FM source.
AM antenna and ground terminals
Connect the supplied AM loop antenna. Use the
terminals marked “AM” and “GND”. The supplied AM
loop antenna will provide good AM reception in most
areas. Position the loop antenna until you hear the
best reception.
e AUDIO IN/OUT (CD, TAPE, CD-R/
MD, TV, DVD, VCR, DSS/VCR2)
These are the analog audio inputs and outputs. There
are 7 audio inputs (4 of which are linked to video
inputs) and 3 audio outputs (1 of which are linked to
video outputs). The audio jacks are nominally labeled
for cassette tape decks, compact disc players, DVD
players and etc.... The audio inputs and outputs
require RCA-type connectors.
r VIDEO IN/OUT
(TV, DVD, VCR, DSS/VCR2)
These are the video inputs and outputs. There
are 4 video inputs and 1 video outputs and each
one includes both composite video and S-video
confi gurations. Connect VCRs, DVD players, and
other video components to the video inputs.
The video output channel can be used to be
connected to video tape recorders for making
recordings.
The input signals of video and S-video are converted
each other, and each of the converted video signals
can be output.