Filter
Top Products
@
PTY (Program Type)
In the PTY mode, the preset buttons
become program type buttons. With
each preset you can select one pro-
gram type, such as for example
NEWS, SPORT, ROCK, CLASSICL,
etc.
@
SRC (source)
You can switch between the different
audio sources radio, tape, and CDC/
AUX (if activated).
@
DIS
Radio ooeration
When an RDS station is received,
press the
DIS
button and the frequen-
cy will be displayed for approximately
four seconds.
TaDe
ODeratiOf7
When pressing the DIS button, the sta-
tion name or frequency will be dis-
played for approximately four seconds.
.*
@LD
Loudness
-
When listening at a low
level, the Loudness function creates a
more natural sound by boosting the
low frequency range.
LD on/off: Press the button.
When the Loudness function is active,
“LD” will light up in the display.
See chapter “DSC programming” for
more information.
@
DSC (Direct Software Control)
Use the DSC function to customise
certain programmable, basic settings
to suit your personal needs and prefer-
ences. See chapter “DSC program-
,ming”
for more information.
Chanaer operation (optional)
To switch the display mode and select
between name, time (playback time)
and number (disc number):
l Press
DIS
briefly.
@
RM
(Radio Monitor)
Press this button to listen to the radio
while fast forwarding or rewinding the
tape.
To switch RM on/off: Press RM.
When this function has been activated,
“RM” shows on the display panel.
The radio is played back during fast
tape run.
’
Fress to eject the tape.
@
1,
2,3,
4, 5, 6
-
preset buttons
On FM, you can store six stations for
each of the memory banks I, II and T.
On AM, you can store six stations.
To store a station: Press a preset
button during radio operation and hold
down until the set resumes play after
the muting and you hear a beep.
To recall a station: Select the desired
waveband. On FM, also adjust the
corresponding memory bank. Then
press the relevant preset button briefly.
Extra function for preset buttons
To store and recall a PTY program
type.
On FM, vou can store and recall one
program-type on/from each preset but-
ton when PTY is active (“PTY”
lights up in the display).
@
Cassette loading slot
Insert the tape with side A or 1 facing
up, the open side showing to the right.
@
AV
Tape side selector
Press this button to switch over to the
other side during tape operation. The
display shows “TR 1” or “TR 2”.
@B
Dolby B
NR*
Press this button to play back a tape
which has been recorded with Dolby-B
noise reduction. When this button is
pressed, “B“ lights up in the display.
*
Noise Reduction system manufactured under li-
cense from Dolby Laboratories Licensing Cor-
poration, “Dolby“ and the double-D symbol are
trademarks of Dolby Laboratories Licensing COP
poration.
@
GE0
@
AUD
To adjust the balance (left/right) and
To adjust the treble and bass frequen-
fader (front/rear) with the rocker
ties
with the rocker switch.
switch.
A
Fader front
V
Fader rear
<< Balance left
>>
Balance right
The last setting will be stored automat-
ically.
To switch off GEO: Press button once
again.
If the setting remains unchanged
within four seconds, the display will
switch back to the previous condition._
A
Treble +
V
Treble
-
xc
Bass
-
>> Bass +
The last setting will be stored automat-
ically.
To switch off AUD: Press button once
again.
If the setting remains unchanged with-
in four seconds, the AUD setting will
be terminated automatically.
9
10