Filter
Top Products
47-EN
& Left Rear (+) Speaker Output Lead (Green)
(CDA-7897 only)
( Left Rear (–) Speaker Output Lead (Green/Black)
(CDA-7897 only)
) Left Front (–) Speaker Output Lead (White/Black)
(CDA-7897 only)
~ Left Front (+) Speaker Output Lead (White)
(CDA-7897 only)
+ Ai-NET Connector
Connect this to the output or input connector of other
product (CD Changer, Equalizer, etc.) equipped with Ai-
NET.
NOTE
You can input TV/video sound by connecting an optional Ai-
NET/RCA Interface cable (KCA-121B) to this component.
, DC/DC Converter
NOTES
•
Do not install the converter at a location subjected to water such as
under the floor mat or air conditioner. This may cause a malfunction.
• Do not bundle the DC/DC converter cable with other audio
cables. Doing so may induce noise into your system.
• Keep the DC/DC converter away from the Antenna cables and
the rear side of the unit, otherwise noise may be generated
when receiving radio broadcast.
- Ai-NET Cable (Included with CD Changer)
. Front Output RCA Connectors
RED is right and WHITE is left.
/ Rear Output RCA Connectors
RED is right and WHITE is left.
: Subwoofer RCA Connectors
RED is right and WHITE is left.
; RCA Extension Cable (Sold Separately)
< System Switch
When connecting a processor or divider using Ai-NET, place
this switch in the EQ/DIV position. When no device is
connected, leave the switch in the NORM position.
NOTE
Be sure to turn the power off to the unit before changing the
switch position.
= Setting the 3WAY/2 WAY switch
Set the 3way/2way Switch according to your audio system.
1 Antenna Receptacle
2 Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna,
if applicable.
NOTE
This lead should be used only for controlling the vehicle's power
antenna. Do not use this lead to turn on an amplifier or a signal
processor, etc.
3 Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
4 Audio Interrupt In Lead (Pink/Black)
5 Illumination Lead (Orange) (CDA-7897 only)
This lead may be connected to the vehicle's instrument
cluster illumination lead. This will allow the backlighting of
the CDA-7897 to dim whenever the vehicle's lights are
turned on.
6 Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle's fuse
box or another unused power source which provides (+)12V
only when the ignition is turned on or in the accessory
position.
7 Battery Lead (Yellow)
Connect this lead to the positive (+) post of the vehicle's
battery.
8 Ground Lead (Black)
Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is
securely fastened using the sheet metal screw provided.
9 Choke Coil with Fuse Holder
(7.5A ..... CDA-7998 only)
(15A ...... CDA-7897 only)
! Power Supply Connector
" Right Front (+) Speaker Output Lead (Gray)
(CDA-7897 only)
# Right Front (–) Speaker Output Lead (Gray/Black)
(CDA-7897 only)
$ Right Rear (–) Speaker Output Lead (Violet/Black)
(CDA-7897 only)
% Right Rear (+) Speaker Output Lead (Violet)
(CDA-7897 only)
The system whose frequency range is divided between
the high frequency range and the low frequency range.
The system whose frequency range is divided among
the high frequency range, mid frequency range, and
the low frequency range.
NOTES
• Use the SUB-W output cord to connect the unit to the Low Range speaker.
• You can use the built-in amplifier to output the Front output/Rear output.
• You cannot adjust the FADER when setting to 3WAY.
The position of switching the switch: F/R/Sub-W
The position of switching the switch: w
Output of this unit :
Front output Rear output SUB-W output
High range
speaker (L)
Mid range
speaker (L)
High range
speaker (R)
Mid range
speaker (R)
Low range
speaker (L)
Low range
speaker (R)
Front high range
speaker (L)
Rear high range
speaker (L)
Front high range
speaker (R)
Rear high range
speaker (R)
Low range
speaker (L)
Low range
speaker (R)