Filter
Top Products
3 – Playback operations—CALL playback
TASCAM CD-RW2000
17
3.4 CALL playback
The
CALL
keys (
L
and
K
) allow the unit’s play-
back position to be returned to the point at which
playback last started from pause mode. If there is no
“call point” (i.e. playback starting from pause),
pressing the
CALL
key will have no effect. It should
also be noted that this call function is available in
play and pause modes only.
Note that the call mode is not available when shuffle
mode has been selected (see 3.1.3, “Playback
modes”) and there is no “call point” set.
3.5 Auto Ready function
This function allows the playing back of a single
track, and the automatic cueing of the next track
ready for playback.
The unit is cued to the start of the track as determined
by the subcode, not the start of the audio signal,
unless the
AUTO CUE
function is on (see 3.6, “Auto
Cue function”).
The unit will enter pause mode in the continue, shuf-
fle and programmed play modes, after the location
has taken place.
If repeat is active (see 3.3, “Repeat play”), the unit
will enter play ready mode at the start of the next
track (
REPEAT ALL
), or the start of the track which is
being repeated (
REPEAT 1
).
To set the function:
1
Repeatedly press the
MENU
key (
9
or
6
)
until the display shows
A_READY>XXX
where
XXX
is either
ON
or
OFF
.
2
Use the
MULTI DIAL
control
B
or the
SKIP
keys
H
to set the function to
ON
.
When the function is on, the
A-READY
display
indicator is lit.
3.6 Auto Cue function
The Auto Cue function allows you to set up the unit
so that when a track is selected for playback in pause
mode (cued), playback will start, not at the first posi-
tion of the track as indicated by the subcode, but at
the first position of the track where the audio level
exceeds a set trigger level.
The trigger level is the same as the recording trigger
level, as set in 4.3.1, “Synchronized recording”. Con-
sult this section on how to set the trigger level.
To set the Auto Cue function on:
1
Repeatedly press the
MENU
key (
9
or
6
)
until the display shows
A_CUE > XXX
where
XXX
is either
ON
or
OFF
.
2
Use the
MULTI DIAL
control
B
or the
SKIP
keys
H
to set the function to
ON
.
When the function is on, the
A-CUE
display indi-
cator is lit.
NOTE
When using the Auto Cue function, there may be a
short “click” sound output through the
DIGITAL
COAXIAL
and
OPTICAL
OUT
terminals (
X
and
Y
)
as the unit locates to the audible start of the track just
before it enters pause mode. However, this sound will
not be output through the
DIGITAL
AES/EBU
OUT
terminal
W
.
3.7 Incremental play
Incremental playback means that when the
STOP
key
G
or
I
is pressed (or if a STOP signal is received
through the
CONTROL
connector
T
) while a track
is being played back, the playback position will be at
the start of the next track.
If the
PLAY
key
H
is pressed while the incremental
playback mode is on, playback starts from the start of
the next track.
To set the incremental play mode on:
1
Repeatedly press the
MENU
key (
9
or
6
)
until the display shows
INC PLAY>XXX
where
XXX
is either
ON
or
OFF
.
2
Use the
MULTI DIAL
control
B
or the
SKIP
keys
H
to set the function to
ON
.
Although there is no indication when the incre-
mental play mode is selected, you will notice
that is in operation whenever you stop play-
back of a track.