Filter
Top Products
3 – Playback operations—Programmed order playback
16
TASCAM CD-RW2000
NOTE
Selecting the playback mode is only possible using
the remote control unit. It is not possible to select the
playback mode using the main unit alone.
1
Press the
PLAY MODE
key
A
repeatedly to
cycle the display through the following:
•
Program
(see 3.2, “Programmed order play-
back” below). The red
PROGRAM
display indicator
lights in this mode.
•
Shuffle
(random track order). In this mode,
each track is played once before the disc repeats.
Using the track search functions will move back-
wards or forwards through the random order, e.g. if
track 7 is followed by track 10, it is possible to use
the track search keys to go back to track 7, which is
remembered as being before immediately before
track 10. The red
SHUFFLE
display indicator lights
in this mode.
•
Continue
. Normal playback mode. Pro-
gramming is cancelled, and playback continues in
the normal order.
The selected mode is shown in large characters and
disappears from the display a few seconds after
selecting the mode, when the display returns to its
previous mode.
3.2 Programmed order playback
The steps to set up to 25 program steps (tracks) to be
played back in a specified order are as follows:
1
Press the
PLAY MODE
key
A
until the display
shows
Program
.
2
The display changes to show
0
Tr
0:00 00
,
meaning that no program steps have yet had
tracks assigned to them.
3
Use the number keys to enter a track number
(including the
+10
key to enter values greater
than 9, as described in 3.1.2, “Track search”).
There is no need to press
ENTER
.
The track entered is assigned to the program
step, and the display changes, showing the
track number, the total time of the program so
far, and the step number, e.g.
2
Tr
14:56 03
.
4
The next program step can then be entered.
NOTE
Steps 3 and 4 above can be carried out from the
main unit by turning and pushing the
MULTI DIAL
control
B
.
5
Repeat steps 3 and 4 above until the program is
complete.
6
Press the
PLAY
key (
H
or
L
) to start playback
at the first program step.
The display shows the track, the current time
display, and the program step number.
While in programmed playback mode, using
the
SKIP
keys
H
or the
MULTI DIAL
control
B
moves backwards and forwards in the order
set in the program.
Use the
PAUSE
key (
I
or
J
) to halt playback tem-
porarily or the
STOP
key (
G
or
I
) to stop playback
of the program.
If the
STOP
key is used, when playback is restarted,
it starts from the first program step.
Clear the program by pressing
PLAY MODE
A
until
the display shows
Continue
. The program is
also cleared when the disc tray is opened, and if the
STOP
key is pressed when playback is stopped in
programmed order mode.
The programmed play order is not memorized when
power is turned off.
If an attempt is made to enter more than 25 program
steps, the message
PGM Full !
appears on
the display.
3.3 Repeat play
The unit can repeat the whole of the disc (or pro-
gram) or the current track only.
NOTE
Selecting the repeat mode is only possible using the
remote control unit. It is not possible to select the
repeat mode using the main unit alone.
1
The unit should be in playback, pause or stop
mode.
2
Continue to press the
REPEAT
key
4
so that
the display shows
Repeat 1
(the
REPEAT 1
indicator lights) to repeat one track, or
Repeat ALL
(the
REPEAT ALL
indicator
lights) to repeat the whole disc or program.
3
If playback has not started, restart it.
To cancel repeat mode, press the
REPEAT
key so that
the display shows
Repeat OFF
and the
REPEAT
indicator goes out.