Filter
Top Products
TASCAM CD-601MKII 15
BASIC OPERATIONS
Details of Transport Key
Operations
READY key (π)
Pressing this key sets the CD player to the online READY
(standby) mode.
To perform online playback, the CD player must first be set
to the online READY mode.
Audio signals are not output from any of the terminals
unless the CD player is in the online READY mode.
Online READY point
The online READY point is as follows according to the state
of the CD player when the READY key is pressed.
• When the tray is open: Start of track 1 on the disc
• In the monitor PAUSE mode: Point when the READY key
was pressed
• When disc operation is stopped/in the monitor playback
mode: Start of track 1 on the disc (when a cue point is
not registered), or the position where monitor playback
was last started from the monitor PAUSE mode (cue
point)
• During online playback (only when the failsafe setting is
OFF): Point when the READY key was pressed
[
NOTE]
• When the failsafe setting is ON, operation of the TRACK,
SEARCH, INDEX, and MENU keys is not accepted in the
online READY mode. (→ page 23 “Failsafe Function”)
ON LINE key (¥)
When this key is pressed in the online READY mode
(READY key is lit), online playback is started. During online
playback, this key is lit (green).
In a mode other than the online READY mode, online
playback is not started even if this key is pressed.
To cancel online playback, press the STOP key.
In the default setting, the online playback signal is output
from all analog /digital output terminals. Note, however,
that the online playback signal can be set in menus not to
be output from the UNBALANCED analog output terminal
and SPDIF digital output terminal. (→ page 22 “Setting the
Terminals for Monitor Output”)
[
NOTE]
• When the failsafe function is ON, operation of keys
other than STOP, PLAY MODE and DISP MODE is not
accepted during online playback. (→ page 23 “Failsafe
Function”)
PLAY/PAUSE key (¥/π)
When this key is pressed while disc operation is stopped,
in the online READY mode or during monitor playback, the
CD player enters the monitor PAUSE mode. When this key
is pressed in the monitor PAUSE mode, monitor playback is
started.
[
NOTE]
• When failsafe is set to OFF, the CD player enters the
monitor PAUSE mode also when this key is pressed
during online playback.
(→ page 23 “Failsafe Function”)
In the monitor PAUSE mode, “PAUSE” is displayed in the
character display area of the display window.
In the default setting, the monitor playback signal is output
from all analog /digital output terminals. Note, however,
that the online playback signal can be set in menus not to
be output from the BALANCED analog output terminal and
AES/EBU digital output terminal. (→ page 22 “Setting the
Terminals for Online Output”)
During monitor playback, the PLAY/PAUSE key is lit yellow,
and in the monitor PAUSE mode, it blinks.
[
NOTE]
• When this key is pressed while the disc tray is open,
the disc tray closes and the CD player then enters the
monitor PAUSE mode at the start of track 1.
• When this key is pressed while disc operations are
stopped, the CD player enters the monitor PAUSE mode
at the start of track 1.
STOP key (ª)
When this key is pressed during online playback, in the
online READY mode, during monitor playback, or in the
monitor PAUSE mode, the disc will stop. This key is lit while
disc operations are stopped.
Note, however, that when the incremental play function
is set to ON, and the STOP key is pressed during online
playback and monitor playback, the CD player stands by at
the start of the next tune to be played at either the online
READY or monitor PAUSE mode according to the auto cue
up setting.
CD-601MKII_Eng.indd 15 3/26/2005 7:39:49 PM