Filter
Top Products
Notes :
• To listen to digital audio signal that is outputting from the
DIGITAL OUTs, you should set the AUDIO OUT to
“SPDIF/BITSTREAM” or “SPDIF/PCM”.(In this case, the
analog audio signal cannot be output from the AUDIO OUTs
of this unit.)
When the AUDIO OUT is not set correctly, loud noise or no
sound may be heard from the speakers, and it may be
harmful to your ears and damages the speakers.(Refer to
“SETTING THE AUDIO SETUP” on page 33.)
• When you connect the MD or CD recorder with a digital
input for digital recording, the AUDIO OUT should be set to
SPDIF/PCM. If not, the digital recording do not perform
properly. (Refer to “SETTING THE AUDIO SETUP” on
page 33.)
• When making the COAXIAL DIGITAL connection, be sure
to use a 75Ω COAXIAL cord, not a conventional AUDIO
cord.
• All of the commercially-available optical fiber cords cannot
be used for audio equipments. If there is an optical fiber
cord which cannot be connected to your audio equipments,
consult your dealer or nearest service organization.
Audio output from the unit’s DIGITAL OUTs
Note 1 : The type of audio output from the DIGITAL OUTs
can be selected by the AUDIO OUT settings.
Note 2 : Sound having 96 kHz sampling is converted into 48
kHz sampling when it is output from the unit’s
DIGITAL OUTs.(Refer to “SETTING THE AUDIO
SETUP” on page 33.)
• Linear PCM is a signal recording format used in music
CDs. While music CDs are recorded in 44.1 kHz/16 bit,
DVD Videos are recorded in 48 kHz/16 bit to 96 kHz/24 bit.
4. AC INPUT CORD
Plug this cord into a wall AC outlet.
5. A/V SCART OUTPUT CONNECTOR (Regional
Option)
Refer to “CONNECTING TO TV WITH SCART
CONNECTOR(Regional Option)” on page 8.
7
ENGLISH
1. Connecting AUDIO OUTs
Connect these jacks to the AUDIO INs of DVD(, AUX, CD,
etc.) of your amplifier or receiver.
Notes :
• To listen to analog audio signal that is outputting from the
AUDIO OUTs, you should set the AUDIO OUT to
“ANALOG”.(In this case, the digital audio signal cannot be
output from the DIGITAL OUTs of this unit.)
• Depending on whether the AUDIO OUTs are connected to
a stereo amplifier/receiver/TV or a A/V amplifier/receiver
with built-in surround decoder, you should set the
DOWNMIX correctly. (Refer to SETTING THE AUDIO
SETUP” on page 33.)
2. Connecting VIDEO OUTs
The COMPONENT VIDEO OUTs of this unit are capable of
outputting either conventional interlacing video signal or
progressively scanned video signal(that can reproduce high-
density pictures with less flicker).
• According to VIDEO OUTs, the excellence in picture
quality is as follows:
Progressive “COMPONENT” > Interlaced “COMPONENT”
> “S-VIDEO” > “(composite) VIDEO”
• When making COMPONENT VIDEO connections, connect
“Y” to “Y”, “C
B” to “C
B”(, “P
B”, “B-Y”), “CR
” to “CR
”(, “PR”, “R-
Y”).
• Depending on the type of the COMPONENT VIDEO INs of
TV, be sure to set the component video output signal to
the corresponding setting.(Refer to “CHANGING THE
COMPONENT VIDEO OUTPUT SIGNAL” on page 26.)
• If there are both VIDEO INs and (MONITOR) VIDEO OUTs
on your amplifier or receiver, connect these jacks to the
corresponding VIDEO IN jacks of your amplifier or receiver
and (MONITOR) VIDEO OUT jacks of that to the
corresponding VIDEO IN jacks of the TV respectively.
• If there are no VIDEO jacks, connect these jacks to the TV
directly. (Refer to “CONNECTING TO TV WITH AUDIO
AND VIDEO INS” on the next page.)
Notes:
• When the component video output signal is set to
PROGRESSIVE TV, the S-VIDEO and (composite) VIDEO
OUTs can not output the normal video signals. Therefore,
it causes the picture to break up and shake.
• When the progressive video signals are input into the non-
progressive COMPONENT VIDEO INs of your TV, the
picture may not be shown normally, too.
Therefore, when the progressive COMPONENT VIDEO
INs of TV are not connected to, you should set the
component video output signal to INTERLACE TV.
• Do not connect the unit to the TV through a VCR.
Otherwise the picture may be disturbed due to the copy
protection function.
3. Connecting DIGITAL OUTs
You can enhance the sound quality by connecting these
COAXIAL and OPTICAL DIGITAL OUTs to the corresponding
DIGITAL INs of an amplifier, MD recorder, etc.
The digital audio signal from a disc is directly transferred. If
you connect to a DTS or Dolby Digital decoder or an
amplifier with built-in decoder, you can enjoy theater-quality
audio in your home.
Disc
Audio recording
format
Audio output
DVD
Video
Dolby Digital
Dolby Digital bitstream (2~5.1ch) or
PCM(48 kHz/16bit) (2ch) (Note 1)
DTS bitstream or PCM(48 kHz/ 16
bit) (2ch) (Note 1)
PCM(48 kHz/ 16 bit) (2ch) (Note 1)
Linear PCM (48 kHz/16bit) (2ch)
(Note 2) or original signal
Linear PCM (44.1 kHz)
DTS
Linear PCM
(48/96 kHz,
16/20/24bit)
MPEG-2
Linear PCM
CD /
MP3 disc