Filter
Top Products
E-12
Advanced CD or MP3/WMA disc playback (continued)
Notes:
●
A track number higher than the number of tracks on the
disc cannot be selected.
●
During random play, direct search is not possible.
To stop playback:
Press the (CD ) button.
Repeat play can play one track, all tracks or a programmed
sequence continuously.
To repeat one track:
Press the PLAY MODE button repeatedly until “Repeat One”
appears. Press the / (CD / ) button.
To repeat all tracks:
Press the PLAY MODE button repeatedly until “Repeat All”
appears. Press the / (CD / ) button.
To repeat desired tracks:
Perform steps 1 - 5 in “Programmed play” section on this page
12 and then press the PLAY MODE button repeatedly until
“Repeat All” appears.
To cancel repeat play:
Press the PLAY MODE button repeatedly until “Normal”
appears and “ ” disappears.
Caution:
After performing repeat play, be sure to press the (CD )
button. Otherwise, the disc will play continuously.
The tracks on the disc can be played in random order
automatically.
To random play all tracks:
Press and hold the PLAY MODE button on the remote control
until “Random” appears. Press the / (CD / ) button.
To cancel random play:
Press the PLAY MODE button again. “RDM” indicator will
disappear.
Notes:
●
If you press the button during random play, you can
move to the track selected next by the random operation.
On the other hand, the button does not allow you to
move to the previous track. The beginning of the track
being played will be located.
●
In random play, the unit will select and play tracks
automatically. (You cannot select the order of the tracks.)
You can choose up to 32 selections for playback in the order you like.
To cancel the programmed play mode:
During programmed stop mode, press the (CD )
button. The display will show “Memory Clear” and all the
programmed contents will be cleared.
Adding tracks to the programme:
If a programme has been previously stored, the “MEM”
indicator will be displayed. Press the MEMORY button.
Then follow steps 2 to add tracks.
Notes:
● When the disc compartment is opened, the programme
is automatically cancelled.
● If you press the ON/STAND-BY button to enter the
stand-by mode or change the function from CD to
another, the programmed selections will be cleared.
● During the programme operation, random play is not
possible.
A. For example, to choose 13
1
Press the “10+” button once.
2
Press the “1” button.
3
Press the “3” button.
B. For example, to choose 130
1
Press the “10+” button twice.
2
Press the “1” button.
3
Press the “3” button.
4
Press the “0” button.
■ Repeat play
■ Random play (shuffle)
Selected track number
■ Programmed play (CD)
1
While in the stop mode, press the MEMORY button on the
remote control to enter the programming save mode.
2 Press the Numeric buttons on the remote control to
select the desired track.
Note: To select track number 10 or higher, refer ’Direct
track search’ on page 11.
3
Repeat step 2 for other tracks. Up to 32 tracks can be
programmed. If you want to check the programmed tracks,
press the MEMORY button repeatedly. If you make a
mistake, the programmed tracks can be cleared by
pressing the CLEAR button.
4 Press the / (CD / ) button to start playback.
■ Programmed play (MP3/WMA)
1
While in the stop mode, press the MEMORY button to
enter the programming save mode.
2 Press the PRESET
( or )
button on the remote
control to select the desired folder.
Then press Numeric buttons on the remote control to
select the desired tracks.
Note: To select track number 10 or higher, refer ’Direct
track search’ on page 11.
3 Repeat step 2 for other folder/tracks. Up to 32 tracks can
be programmed.
4 Press the / (CD / ) button to start playback.
Selected track number