Filter
Top Products
38
RSX-1067 Surround Sound Receiver
TURN ON VOL: Specifies a default volume
level to be used each time Zone 2 is activated.
You can select LAST to have Zone 2 activate
with the last previously used volume setting.
Or, you specify a volume from MIN (full mute)
to MAX, in 1dB increments. Note that this setting
cannot exceed the MAX VOL established in
the next line of the menu.
MAX VOL: Specifies the maximum volume
level for Zone 2. The volume cannot be ad-
justed above this level. Settings range from MIN
to MAX, in 1dB increments.
12V TRIGGER: The RSX-1067 has three12V
trigger outputs that supply a 12V DC signal
to turn on Rotel components and other com-
ponents as needed. The 12V Trigger labeled
ZONE 2 is assigned to Zone 2 and can send
a turn-on signal to remote components when-
ever Zone 2 is activated. Select the ON set-
ting to have the ZONE 2 trigger output send
the turn-on signal. Select the OFF setting to dis-
able the 12V trigger function for Zone 2.
Default Setup
DEFAULT SETUP
TUNER SETTING:N.America
FRONT REDIRECT:Front
CB REDIRECT:CB
FACTORY DEFAULT:No
USER DEFAULT:No
SET USER DEFAULT:No
MAIN MENU
The DEFAULT SETUP menu provides access to
six functions:
• Set the tuning function for North American
or European frequencies.
• Redirect the front channel amplifiers to
power Zone 2 speakers when an outboard
power amplifier is used for the front speak-
ers.
• Redirect the center back channel amplifi-
ers to power Zone 2 speakers.
• Restore all features and settings to the origi-
nal FACTORY DEFAULT settings.
• Memorize a custom group of settings as
a USER DEFAULT.
• Activate the memorized USER DEFAULT set-
tings.
To change the TUNER setting: Place the
highlight on the TUNER SETTING line using
the UP/DOWN buttons and use the +/– but-
tons to change the setting to N. AMERICA or
EUROPE. Then, move the highlight to the FAC-
TORY DEFAULT line and change the setting to
YES as described above. The screen will
change to a confirmation screen. Press the EN-
TER button to proceed with resetting the FAC-
TORY DEFAULT settings and changing the
TUNER SETTING. To return to the MAIN menu
without resetting the FACTORY DEFAULT and
TUNER settings, change the entry to NO and
press the ENTER button.
To change the FRONT REDIRECT setting:
Place the highlight on the FRONT REDIRECT
line using the UP/DOWN buttons and use the
+/– buttons to change the setting to FRONT
SP (for powering front speakers) or ZONE SP
(for powering speakers in zone 2). If you use
the internal amplifiers to power the remote
speakers, then you will need a separate ste-
reo amplifier to power your front speakers.
To change the CB REDIRECT setting: Place
the highlight on the CB REDIRECT line using
the UP/DOWN buttons and use the +/– but-
tons to change the setting to CB SP (for pow-
ering front speakers) or ZONE SP (for pow-
ering speakers in zone 2). If you use the in-
ternal amplifiers to power the remote speak-
ers, then you will need a separate stereo
amplifier to power your center back speak-
ers.
NOTE
: Changing the default TUNER SETTING
or REDIRECT SETTINGS can only done at the
same time as restoring the FACTORY DEFAULT
settings. Therefore, we recommend selecting
your default TUNER and REDIRECT settings
and resetting to the FACTORY DEFAULT set-
tings as the first step in configuring the unit,
before you change or memorize any other
configuration settings.
To restore the FACTORY DEFAULT set-
tings: Place the highlight on the FACTORY
DEFAULT line using the UP/DOWN buttons
and use the +/– buttons to change the setting
to YES. Press the ENTER button to proceed with
resetting the FACTORY DEFAULT settings. The
unit will power off and then on, with the fac-
tory settings restored. To return to the MAIN
menu without resetting the FACTORY DEFAULT
settings, change the entry to NO and press
the ENTER button.
NOTE
: Resetting to factory default settings will
erase all stored settings including delay set-
tings, speaker settings, balance settings, in-
put settings and more. You will lose ALL system
configuration settings. Be certain that you wish
to do so before resetting the factory defaults.
To memorize USER DEFAULT settings:
Many of the current configuration settings can
be stored as a USER DEFAULT, which can be
activated at any time from this menu screen.
To save the current settings as a USER DEFAULT,
place the highlight on the SET USER DEFAULT
line using the UP/DOWN buttons and use the
+/– buttons to change the setting to YES. Press
the ENTER button to store the new USER DE-
FAULT settings. To return to the MAIN menu
without saving any changes, change all en-
tries on the screen to NO and press the EN-
TER button.
NOTE
: If there is insufficient memory to store a
USER DEFAULT configuration file, the SET
USER DEFAULT option will not be available.
To activate memorized USER DEFAULT
settings: After you have stored a USER DE-
FAULT configuration file, you can activate those
settings at any time by placing the highlight
on the USER DEFAULT line using the UP/
DOWN buttons. Use the +/– buttons to change
the setting to YES. Press the ENTER button to
proceed with activating the USER DEFAULT
settings. To return to the MAIN menu without
activating the USER DEFAULT settings, change
the entry to NO and press the ENTER button.