Filter
Top Products
29
English
Controlling Zone 2
from the Main Room
You can control Zone 2 from the main room
using front panel or remote control buttons to
activate or deactivate Zone 2, change input
sources, and adjust the volume. Controlling
Zone 2 from the main room is accomplished
by pressing the ZONE button on the front panel
or remote, putting the RSX-1067 in Zone 2 con-
trol mode temporarily. When the Zone 2 sta-
tus is displayed, the OSD and/or front panel
displays show the current source selection and
volume in Zone 2 for ten seconds, during which
time you can use the front panel VOLUME
control and INPUT buttons to change the ZONE
2 settings.
To turn Zone 2 on or off:
1. Press the front panel or remote ZONE but-
ton. Zone 2 status appears in the OSD and
front panel displays.
2. Within 10 seconds, press the front panel
or remote ZONE button to toggle Zone 2
on or off.
3. Following 10 seconds with no commands,
the RSX-1067 reverts to normal operation.
To change the Zone 2 input source:
1. Press the front panel or remote ZONE but-
ton. Zone 2 status appears in the OSD and
front panel displays.
2. Within 10 seconds, press one of the IN-
PUT buttons to select a new source for Zone
2. The name of the selected source appears
in the display. Instead of pressing an IN-
PUT button, you can also push the +/–
buttons on the remote to step through the
inputs.
3. Following 10 seconds with no commands,
the RSX-1067 reverts to normal operation.
To change the Zone 2 volume:
1. Press the front panel or remote ZONE but-
ton. Zone 2 status appears in the OSD and
front panel displays.
2. Within 10 seconds, adjust the volume
control on the front panel or remote to
change the Zone 2 output level. The new
setting appears in the display.
3. Following 10 seconds with no commands,
the RSX-1067 reverts to normal operation.
Controlling Zone 2 from the
Remote Location
With a properly configured IR repeater sys-
tem, you have full control of Zone 2 using an
RR-1050 remote from the Zone 2 location. You
can select and operate a source, adjust the
volume, and turn Zone 2 on or off. Whatever
commands you send from the RR-1050 will
change Zone 2 and only Zone 2, just as if
you were controlling a totally independent
audio system in that room. These changes will
have no effect on the main listening room.
To turn Zone 2 on or off, press the ON/OFF
buttons on the remote. To adjust the volume
in Zone 2, press the VOLUME buttons on the
remote. To select a different analog input source,
press one of the DEVICE/INPUT buttons on
the remote. You can also use the +/– buttons
to step through the source inputs.
NOTE
: The volume adjustment is only avail-
able if the Zone 2 outputs are configured to
use VARIABLE levels. With FIXED levels, the
volume control for Zone 2 is disabled.
SETUP
The RSX-1067 features two types of informa-
tion displays to help operate the system. The
first consists of simple status displays that appear
on the TV screen and/or front panel display
whenever primary settings (Volume, Input, etc.)
are changed. These status displays are self-
explanatory.
A more comprehensive ON-SCREEN DISPLAY
(OSD) menu system is available at any time
by pressing the MENU/OSD button on the
remote. These OSD menus guide you through
the configuration and setup of the RSX-1067.
In general, the settings made in the configu-
ration process are memorized as default set-
tings and need not be made again for nor-
mal operation of the unit.
The OSD menus can be configured to display
several different languages. The default English
version of all the menus is shown at the front
of this manual. If your language is available,
those menus will be shown in the following
instructions. If you would like to change from
the default English language before proceed-
ing, go to the instructions for the OTHER OP-
TIONS menu later in this manual. From this
menu, you can change the language display.