Filter
Top Products
26
RSX-1067 Surround Sound Receiver
Cinema EQ
The EQ button (remote only) activates or de-
activates a special CINEMA EQ setting. This
equalization may be desirable for playback
of movie source material to compensate for
the acoustic differences between a commer-
cial cinema and a home theater environment
by reducing the high-frequency content.
The EQ setting is independent for each source
input. Using the button only changes the set-
ting for the currently active source input.
Tuner Controls
The RSX-1067 features a digital synthesized
AM/FM tuner with RDS capability and 30
station presets. The unit offers a wide range
of tuning options. Here is an overview of the
tuning options (more detailed information is
provided in subsequent sections of this manual):
• Manual frequency tuning tunes up or
down to the next station frequency (when
in frequency tuning mode). Press and re-
lease a TUNING button (CH UP/DOWN
on the remote) to tune.
• Direct frequency tuning lets you en-
ter the desired station frequency digits. Press
the DIRECT button (or the FRQ DIRECT) but-
ton on the remote) and enter the digits us-
ing the NUMERIC buttons.
• Automatic frequency search tuning
searches up or down to find the next re-
ceivable broadcast signal. Press and hold
a TUNING button (CH UP/DOWN on the
remote) for at least one second to search
up or down.
• Station preset tuning lets you directly
enter the number of a memorized station
preset. Enter the number of the memorized
preset using the NUMERIC buttons.
• Preset tuning jumps up/down to the next
memorized station preset. When in PRE-
SET mode, press a TUNING button (CH
UP/DOWN on the remote) to select the
next station preset. Press the PRESET but-
ton on the remote to select PRESET tuning
mode. Press the TUNE button on the remote
to select FREQUENCY tuning mode. Press
the P-TUN button on the remote to toggle
between preset and frequency tuning
modes.
• Preset scan tuning automatically scans
through the memorized station presets,
playing each for 5 seconds. Press the SCAN
button on the remote to begin preset scan-
ning. Press the button again to stop the
scanning and listen to the desired preset.
• RDS (Europe) or RBDS (USA) tuning
provides a range of special tuning and
search features based on data codes en-
coded with the broadcast signal. See the
RDS section of this manual for detailed
information.
NOTE
: The RSX-1067 comes configured for tun-
ing in the market where you purchased it (N.
America or Europe). To change this default set-
ting, see the information on the DEFAULT SETUP
on-screen menu later in this manual.
BAND Buttons
Press the BAND button to toggle between AM
and FM reception. An indicator in the front-
panel display confirms your choice and the
currently tuned station frequency is shown.
TUNING Buttons
The TUNING buttons (labeled CH UP/DOWN
on the remote control) provide three different
tuning functions, depending on the mode of
operation.
In the normal FREQUENCY tuning
mode, press a TUNING button (CH UP/
DOWN on the remote) and release to manu-
ally jump to the next station frequency, regard-
less of whether or not a station is broadcast-
ing on that frequency. For auto frequency search
tuning, press and hold the TUNING button for
approximately one second. An AUTO indicator
will appear in the front-panel display and the
tuner will begin scanning up or down through
the frequencies until the next available signal
is detected. If this is not the desired station,
repeat the automatic tuning procedure to find
the next station. Weak stations will be skipped
during auto tuning.
NOTE
: Select the FREQUENCY tuning mode
by pressing the TUNE button on the remote
or toggle between FREQUENCY and PRESET
modes by pressing the P-TUN button.
In the PRESET tuning mode, press a
TUNING button (CH UP/DOWN on the re-
mote) and release to jump to the next memo-
rized station preset.
NOTE
: Select the PRESET tuning mode by press-
ing the PRESET button on the remote or toggle
between FREQUENCY and PRESET modes by
pressing the P-TUN button. A PRESET indica-
tor appears in the display when PRESET TUN-
ING is activated.
In the RDS PTY search mode, press a
TUNING button (CH UP/DOWN on the re-
mote) to select the desired program type from
the scrolling list in the display. See the section
on RDS tuning for more details.
NOTE
: Several indicators in the front-panel dis-
play assist tuning. A large display shows the
tuned frequency. A TUNED indicator lights
when a sufficiently strong signal is received.
A ST indicator lights when a stereo FM signal
is received.
MEMORY Button
The MEMORY button is used with the NUMERIC
buttons to store memorized station presets. See
the next section for detailed instructions.
NUMERIC Buttons:
Station Presets
The RSX-1067 can store up to 30 station pre-
sets for recall at any time using the NUMERIC
buttons on the front panel. To memorize a sta-
tion:
1. Tune to the desired station, AM or FM.
2. Press the MEMORY button on the front-
panel. A MEMORY indicator will flash for
five seconds in the front-panel display.
3. While the MEMORY indicator is flashing,
press the number of the preset where you
wish to store the station frequency. For
example, to memorize the station as pre-
set 3, press the 3 button. To memorize preset
15, press the 1 button followed by the 5
button.
4. A previously stored frequency is erased from
memory when a new frequency is memo-
rized for the same preset number.
To tune to a previously memorized station, just
press the preset number on the NUMERIC
buttons. For example, to tune to preset 3, press
the 3 button. To tune to preset 15, press the 1
button and then press the 5 button.