Filter
Top Products
7
Important Notes on Making Connections
and Switching the Power On and Off
921
• To prevent malfunction and/or damage to speakers or other devices,
always turn down the volume, and turn off the power on all devices
before making any connections.
924
• To prevent the inadvertent
disruption of power to your unit
(should the plug be pulled out
accidentally), and to avoid
applying undue stress to the AC
adaptor jack, anchor the power
cord using the cord hook, as
shown in the illustration.
926
• When connection cables with
resistors are used, the volume
level of equipment connected to
the inputs (control/power input and control I/O terminals) may be low.
If this happens, use connection cables that do not contain resistors.
941
• Once the connections have been completed, turn on power to your
various devices in the order specified. By turning on devices in the
wrong order, you risk causing malfunction and/or damage to speakers
and other devices. (When turning the power off, reverse this procedure.)
Connected device
→
AR-200
→
Power amp, etc.
942
• This unit is equipped with a protection circuit. A brief interval (a few
seconds) after power up is required before the unit will operate normally.
• To avoid risk of electric shock, do not touch the connectors while the unit
is in operation.
• Never remove a card during recording of phrases. Furthermore, do not
turn off the power or remove the AC adaptor cord during recording of
phrases. Doing so may damage the card.
• To avoid the risk of malfunction and/or damage, insert only
CompactFlash card into the MEMORY CARD slot. Never insert any
other type of card. Avoid getting paper clips, coins, or any other foreign
objects inside the drive.
930 (modified)
• Do not remove the CompactFlash card while the card is being accessed.
Doing so may corrupt the unit’s data or the data on the CompactFlash card.
931
• Carefully insert the CompactFlash card all the way in—until it is firmly
in place.
The AR-200S is not equipped with a power switch. Power is turned on when
electricity is supplied to the AC adaptor jack, or to the control/power input, or
control I/O terminals’ DC IN.
Supplied AC adaptor: ACI or PSB series
Control/Power Input and Control I/O terminals’ DC
IN specifications
Voltage: 9 to 24 V DC
Current: 1200 mA
* Refer also to
DC Power Supply
(p. 23).
Do not supply electrical power simultaneously to multiple terminals;
doing so may result in damage to the unit.
Cord Hook
The cord of
the supplied
AC Adaptor
To the Power Outlet
Connecting Cables to the Audio Input
and Output Terminals
Turning On the Power
Euroblock
Connector
Connect to
audio input and output terminals
on the AR-200S’s rear panel
Use a commercially
available flat-head
screwdriver to secure
the cable ends
Insert the cables
Cards Handled by the AR-200S
With the AR-200S, recorded audio and non-audio information (phrase data) is
stored on cards.
Optional Roland CompactFlash cards (PM-***-CF Series) are
recommended for use with the AR-200S.
Up to a maximum of 1000 phrases can be saved to cards formatted with the
AR-200S.
* To format a card on the AR-200S, transmit the format command via the RS-
232C port.
•
When Inserting
Insert the card all the way into the card slot.
* Insert the card straight into the slot, with the card label facing upwards.
•
When Removing
To remove the card, press the eject button.
Press the eject button firmly, all the way in.
* Never remove a card during recording, playback, or formatting. Furthermore, do
not turn off the power or remove the AC adaptor cord during recording,
playback, or formatting. Doing so may damage the card.
The AR-200S’s file format is the same as the format for the AR-3000/200.
Using Cards Formatted on Earlier Model Units
with the AR-200S
• Files on PC cards used on AR-3000/200/2000/100 models can be used by
copying the data to CompactFlash with the ARE-3000.
(Cards copied using AR models cannot be used.)
Using Cards Formatted on the AR-200S with
Earlier Models
• Cards can be used as is with the AR-3000/200 by copying the data to PC
card (PM series) with the ARE-3000.
• Cards cannot be used with the AR-2000/100.
(Cards copied using other AR models cannot be used.)
Please download the ARE-3000 (free of charge) from the following URL.
http://www.rssamerica.com/
Important Notes on Handling Cards
CompactFlash™
Side with arrow
should face upwards
Card Compatibility with Other Models
in the AR Series
AR-200S_e.book 7ページ ２００５年１２月８日 木曜日 午前９時３分