Filter
Top Products
Controlling the rest of your system
09
69
En
Similar to Multi operations, System off allows you to use
two buttons to stop and switch off a series of components
in your system at the same time.
1
Only one System off
operation sequence may be programmed.
Press
MULTI OPERATION
and then
SOURCE
to:
1. Transmit a sequence of up to five programmed
commands.
2. Switch off all Pioneer devices including the receiver
(except DVD recorders and VCRs).
For greater convenience, program this receiver to
perform power on/off and playback operations on non-
Pioneer devices as well.
2
(The signals for Pioneer devices
described above are not contingent on programming for
non-Pioneer devices.)
The buttons that can be programmed using Multi
operation or System off are the same buttons as those
that can be programmed for other remote controls (see
Programming signals from other remote controls on
page 67).
Programming a Multi operation or a
shutdown sequence
1 Press and hold
R.SETUP
, then press “3” for three
seconds.
The LED flashes continuously.
• To cancel the preset setup mode press R.SETUP.
2 Press the input function button (or
SOURCE
button).
For Multi operations, press the input function you wish to
program (for example, if you want to start the sequence
by switching on your DVD player, press DVD)
3
.
For System off, press the SOURCE button.
The LED blinks twice and flashes continuously.
3 If necessary, press the input function button for the
component whose command you want to input.
This is only necessary if the command is for a new
component (input function).
4 Select the button for the command you want to
input.
The LED blinks once and flashes continuously.
• You don’t need to program the receiver to switch on
or off. This is done automatically.
With Pioneer components, you don’t need to program
the power to switch off in a shutdown sequence (except
DVD recorders).
5 Repeat steps 3 to 4 to program a sequence of up to
five commands.
If you press R.SETUP before programming is completed,
commands programmed up to that p oint will be stored.
6Press
R.SETUP
to exit the programming mode.
Using multi operations
1Press
MULTI OPERATION
.
The LED flashes continuously.
2
Within five seconds, press
an input function
button that has been set up with a multi operation.
The receiver switches on (if it was in standby) and the
programmed multi operation is performed automatically.
Using System off
1Press
MULTI OPERATION
.
The LED flashes continuously.
2
Within five seconds,
press
SOURCE
.
The command sequence you programmed will run, then
all Pioneer components will switch off
4
, followed by this
receiver (switch of all the zones becomes off).
Erasing the settings for the multi-operation
This erases all the settings programmed in the remote
control for the multi-operation.
1 Press and hold
R.SETUP
, then press “8” for three
seconds.
The LED flashes continuously.
• To cancel the preset setup mode press R.SETUP.
2 Press the input function button containing the
program you want to cancel or the
SOURCE
button
for three seconds.
If the LED lights for one second, the erasing has been
successfully completed.
Note
1• Before Multi operation and System off will work correctly, you must setup the remote to work with your TV and other components (see
Operating multiple receivers on page 66 for more on this).
• Some units may take some time to power up, in which case multiple operations may not be possible.
• Power on and off commands only work with components that have a standby mode.
2Some remote controllers for other manufacturers' devices use the same signals for switching the power on and off. In some cases, even if this
receiver is programmed to perform these commands, power to the non-Pioneer devices may not be switched on and off correctly. Program
the rec
eiver to perform these commands if the non-Pioneer device uses separate signals for power on/off.
3 With Multi operation, the HDMI and TV CTRL settings cannot be made. For other settable input functions, see Setting the remote to control
other components on page 66.
4In order to avoid accidently switching off a DVD recorder that is currently recording, no DVD recorder power off codes are sent.
VSX-1325_UXJCB.book 69 ページ ２０１０年３月９日 火曜日 午後３時４分