Filter
Top Products
Message Cause Action
Start upthe
Pandora Ap-
plication
from your
Device.
The Pandora ap-
plication has
not startedrun-
ning yet.
Start upthe
Pandora applica-
tion fromyour
iPhone.
Unable to
save thumb
rating. Try
again later.
Unable tosave
thumb rating.
Try again later.
Unable to
save Book-
mark. Try
again later.
Unable tosave
Bookmark.
Try again later.
Pandora sys-
tem mainte-
nance. Try
again later.
Pandora system
is undergoing
maintenance.
Try again later.
Skip limit
reached.
Skip limit
reached.
Do notexceed the
skip limit.
This version
of the
Pandora Ap-
plication is
not sup-
ported.
This versionof
the Pandoraap-
plication isnot
supported.
Connect an
iPhone thathas a
compatible ver-
sion ofthe
Pandora applica-
tion installed.
Check Device Deviceerror
message dis-
played inthe
Pandora appli-
cation.
Please checkyour
iPhone.
Pandora is
unable to
play music.
Please see
your Device.
Unable toplay
music from
Pandora.
Please checkyour
iPhone.
Message Cause Action
Create sta-
tion within
the Pandora
Application
on Device.
No station
found.
Create astation
in thePandora
application on
your iPhone.
No Active
Station
No stationse-
lected.
Select astation.
Communica-
tion erroroc-
cured. Please
reconnect
your device.
If thereis no
ACK after10 at-
tempted retries
at 750ms,the
accessory
should assume
that communi-
cation isinter-
rupted and
disconnect
from
PandoraLink.
Please reconnect
your iPhoneand
try again.
Device has
not been
registered.
Go to
Bluetooth
Connection
Menu to
register.
No Bluetooth
device found.
Followthe in-
structionsthat ap-
pear onthe
screen.
BTerror.
Press BAND
key toretry.
Bluetooth con-
nection failed.
Followthe in-
structionsthat ap-
pear onthe
screen.
Start up
Pandora.
Press BAND
key toretry.
Connection to
the Pandoraap-
plication failed.
Followthe in-
structionsthat ap-
pear onthe
screen.
Check
Pandora.
Press BAND
key toretry.
Connection to
the Pandoraap-
plication failed.
Followthe in-
structionsthat ap-
pear onthe
screen.
Message Cause Action
Disconnect-
ed.Press
BAND keyto
retry.
Bluetooth con-
nection lost.
Followthe in-
structionsthat ap-
pear onthe
screen.
Understanding auto EQ error
messages
When correct measurementof the car’s interior
acoustic characteristics isnot possible using
auto EQ, anerror message may appear on the
display.In such cases, refer to thetable below to
see what the problemis and how it maybe cor-
rected. After checking, try again.
Message Cause Action
Please con-
nect themi-
crophone for
measure-
ment. When
finished,
please push
HOME key.
The microphone
is notcon-
nected.
Plug theoptional
microphone se-
curely intothe
jack.
Error. Please
check xxxx
speaker.
The microphone
cannot pickup
the measuring
tone ofa speak-
er.
! Confirmthat
the speakersare
connected cor-
rectly.
! Correctthe
input levelsetting
of thepower amp
connected tothe
speakers.
! Plugthe micro-
phone securely
into thejack.
Message Cause Action
Error. Please
check noise.
The surround-
ing noiselevel
is toohigh.
! Stopyour carin
a placethat is
quiet, andswitch
off theengine, air
conditioner and
heater.
! Setthe micro-
phone correctly.
Error. Please
check bat-
tery.
Power is not
being supplied
from thebatter y
to thisunit.
! Connectthe
battery correctly.
! Checkthe bat-
tery voltage.
Understanding messages
Messages Translation
Screen imagemay
appear reversed.
Pioneer recommends
the useof acamera
which outputsmirror-
reversed images.Oth-
erwise, thescreen
image willappear re-
versed.
Additional information
56
Appendix
Additional information
En
<CRD4703-B/N>56