Filter
Top Products
84
Zone 2—Continued
Controlling Zone 2 with the Remote
Controller
Note:
• To control Zone 2, you must press the remote control-
ler’s [ZONE 2] REMOTE MODE button first.
Adjusting the Volume for Zone 2
To Mute Zone 2:
Press the remote controller’s [ZONE 2] button, followed
by the [MUTING] button. To unmute Zone 2, press the
remote controller’s [ZONE 2] button again, followed by
the [MUTING] button, or adjust the volume for Zone 2.
Notes:
• Only analog input sources are output by the ZONE 2
LINE OUT and ZONE 2 SPEAKERS terminals. Dig-
ital input sources are not output. If no sound is heard
when an input source is selected, check to see if it’s
connected to an analog input.
• When the ZONE 2 SPEAKERS terminals are used,
listening modes that require surround back speakers,
such as Dolby Digital EX, DTS-ES, and THX Select2
Cinema, are unavailable.
• While Zone 2 is on, the functions do not work.
• You can’t select different radio stations for the main
room and Zone 2. The same radio station will be used
for both.
1
Press the [ZONE 2] REMOTE
MODE button, then point the
remote controller at the AV
receiver and press the [ON] but-
ton.
Zone 2 turns on, and the ZONE 2 12V
TRIGGER OUT goes high (+12 V).
2
To select an input source for
Zone 2, press the [ZONE 2]
REMOTE MODE button, followed
by an INPUT SELECTOR button.
To select AM, FM, or XM, press the
[TUNER] INPUT SELECTOR button
repeatedly.
3
To turn off Zone 2, press the
[ZONE 2] REMOTE MODE button,
followed by the [STANDBY] but-
ton.
THX
10
--/---
11 12
REMOTE MODE
HDD
RECEIVER
TAPE/AMP
DVD CD
ZONE2
STEREO
SURR
DIRECT
SUBTITLEAUDIO
ALLST
PLAY MODE
VIDEO OFF
REPEAT
OPEN/CLOSE
Re-EQ
+
-
TV CH
TV VOL
LISTENING MODE
INPUT SELECTOR
32
MACRO
1
+
10 0
CLEAR
12
3
456
789
INPUT
I
ON STANDBY
TV
CD
V1 V2 V3
MULTI CH
DVD
TUNER
PHONO
V4
TAPE
PURE A
TEST TONE
CH SEL LEVEL LEVEL
L NIGHT
RC-620M
ZONE2
ON
STANDBY
LEVEL–,
LEVEL+
INPUT
SELECTOR
ZONE2
ON
ZONE2
123
46
789
CD
V1
V4
V2 V3
DVD
TAPE
TUNER
+
10
PHONO
ZONE2
STANDBY
1
On the remote controller, press
the [ZONE 2] REMOTE MODE but-
ton, and then use the [LEVEL–]
and [LEVEL+] buttons.
On the AV receiver, use the ZONE
2 LEVEL [ ]/[ ] buttons.
If your Zone 2 speakers are connected
to an amp in Zone 2, use its volume
control to adjust the volume.
OFF TONEZONE 2
ZONE 2 LEVEL
PHONES
STEREO
DIMMERMEMORY
LISTENING MODE
TUNING
MODE
SETUP
PRESET PRESET
TUNING
RETURN
ENTER SETUP MIC
VIDEO
S VIDEO
DIGITAL
VIDEO 4 INPUT
AUDIOLR
CLEAR
STANDBY/ON
STANDBY
MASTER VOLUME
PHONO
ZONE 2
DISPLAY
PURE AUDIO
TUNERTAPE
VIDEO 4VIDEO 3VIDEO 2VIDEO 1
DVDMULTI CH CD
OFF
ON
POWER
ZONE 2 LEVEL ,
ZONE2
LEVEL LEVEL
ZONE 2 LEVEL
AV receiver